DESIGN GU I D E L I N E S
Revised
Effective September 2016
2003 CONTRIBUTORS : 2016 CONTRIBUTORS :
VITA, Planning & Landscape Architecture BOARD OF DIRECTORS, CVE
NFA ARCHITECTS, Architecture DESIGN REVIEW COMMITTEE, CVE
TETRA TECH, Civil Engineers
DISCOVERY IRONWOOD INVESTORS, LLC, Community Developer
2
PREFACE
These Design Guidelines (Guidelines)
are intended to provide guidance for all
development and construction—new
buildings, building additions, site work
and landscaping—as well as any
subsequent changes or alterations to
previously approved plans or existing
homes. The Guidelines will be
administered and enforced by the
Canyon View Estates Design Review
Committee (DRC) in accordance with
procedures set forth in the Declaration of
Covenants, Conditions and Restrictions
for the Canyon View Estates at
Ironwood Country Club (CC&R’s)
recorded with the State of California,
and as may be amended thereafter. In the
event of any conflict between the Design
Guidelines and CC&R’s, the CC&R’s
shall govern and control.
The Guidelines may also be amended
from time to time by the DRC. It is the
Homeowner’s responsibility to be sure
that they have current Guidelines and
have carefully reviewed all applicable
sections of the CC&R’s.
The illustrations in this document are
intended to convey a concept, and not to
portray specific plans for construction.
The purpose of these Guidelines is not to
create look-alike structures or other
Improvements but to ensure that designs
are compatible with the site, the overall
desert environment and the design
objectives of the Community as a whole.
To that end, the DRC reserves the right
to require design modifications or
additions that, though not specifically
contained in the Guideline text or
illustrations, are within the spirit and
intent of the Guidelines and the design
objectives of the Community.
These Guidelines are binding on any
persons, company or firm that intends to
construct, reconstruct or modify any
permanent or temporary Improvements
in the Community or in any way alter
their Lot, surrounding area or the natural
setting of the desert environment.
The CC&R’s accompanying these
Guidelines have been adopted and
recorded to establish the Community
Association (“Association”) and the
Association rules and regulations.
Homeowners and their Consultants and
contractors should familiarize
themselves with these rules prior to the
start of design or construction.
These Guidelines address custom and
production home residential
Improvements in all proposed phases.
Homeowners should refer to appropriate
sections in these Guidelines and the Lot
Diagrams for conditions governing
Improvements on their Lot.
3
TABLE OF CONTENTS
1 CANYON VIEW ESTATES AT IRONWOOD COUNTRY CLUB DESIGN
PHILOSOPHY
1.1 An Introduction to the Canyon View Estates 8
1.2 The Neighborhood Plan 8-9
2 SITE AND LANDSCAPE GUIDELINES
2.1 Site and Landscape Objectives 10
2.2 Lot Diagrams 11
2.3 Building Envelopes 11
2.3.1 Private Area 11-12
2.3.2 Transition Area 12
2.4 The Natural Area 12
2.5 Combining Lots 12
2.6 Building Coverage and Minimum Floor Area 13
2.7 Grading and Drainage 13-15
2.7.1 Retaining Wall Guidelines 14
2.7.2 Drainage Guidelines 14-15
2.8 Driveways and Auto Courts 15-16
2.9 Garages and Parking 16
2.10 Paths, Outdoor Stairs, Courtyards and Terraces 17
2.11 Walls, Fences & Gates 17-18
2.12 Landscape Structures 19
2.13 Planting 19-22
2.13.1 General Planting Guidelines 19-20
2.13.2 Private & Transition Area Planting Guidelines 21
4
2.13.3 The Natural Area Planting Guidelines 21-22
2.13.4 Existing Streetscape and Landscape on Lots 22
2.14 Pools and Water Features 22
2.15 Irrigation 23
2.16 Lighting 23-24
2.17 Exterior Service Areas 25
2.18 Miscellaneous Site Elements 25-26
2.18.1 Patio Furniture 25
2.18.2 Sculptures and Artwork 25
2.18.3 Barbeques, Heat Lamps and Misting Systems 25
2.18.4 Flagpoles, Antennae, and Satellite Dishes 26
2.18.5 Address Markers and Mailboxes 26
3 ARCHITECTURE GUIDELINES
3.1 Architectural Design Objectives 27
3.2 Desert Architecture 27-28
3.3 Building Height 28
3.4 Building Forms and Massing 28-29
3.5 Roofs 29-30
3.6 Exterior Walls 30-31
3.7 Doors and Windows 31-32
3.8 Building Projections and Accessory Structures 32-33
3.9 Color 33-35
3.10 Decorative Elements 36
3.11 Utilities 36
5
4 LIFE AND SAFETY CONSIDERATIONS
4.1 Energy and Resource Conservation Measures 37
4.2 Skylights 37
4.3 Solar Equipment 38-39
5 DESIGN REVIEW PROCESS
5.1 Overview of Design Review Process 40-41
5.2 Approved Design Professionals 41
5.3 Pre-Design Conference and Schematic Design 41-42
5.3.1 Pre-Design Conference 41
5.3.2 Schematic Design 41-42
5.4 Preliminary Design Review 42-43
5.4.1 Preliminary Design Review
Submission Materials 42-43
5.4.2 Staking 43
5.4.3 Preliminary Design Review Meeting 43
5.5 Final Design Review 44-45
5.5.1 Final Design Review Submission Materials 44-45
5.5.2 Final Design Review Meeting 45
5.5.3 Final Design Approval 45
5.6 Resubmittal of Plans 45
5.7 City of Palm Desert Approvals and Other Agencies 46
5.8 Subsequent Changes 46-49
5.9 Work in Progress Observations 49
5.10 Notice to Comply 49
5.11 Notice of Completion 49
6
5.12 Right of Waiver 49
5.13 Non-Liability 50
5.14 Design Review Schedule 50
5.15 Application Fees 51
5.16 Application Format 51
6 CONSTRUCTION AND BUILDER REGULATIONS
6.1 Pre-Construction Conference 52
6.2 Construction Area 52
6.3 Builder's Bond 53
6.4 Access to Construction Area 523
6.5 Vehicles and Parking Areas 53
6.6 Storage of Materials and Equipment 53
6.7 Construction Activity Times 54
6.8 Construction Trailers and/or Temporary Structures 54
6.9 Sanitary Facilities 54
6.10 Debris and Trash Removal 55
6.11 Hazardous Waste Management 55
6.12 Excavation and Grading 55
6.13 Foundations 56
6.14 Lot Survey 56
6.15 Start of Construction & Temporary Landscape 56
6.16 Damage Repair and Restoration 56
6.17 Project Completion and Close-Out 57
6.18 Construction Observations 57
6.19 Construction Signs 57
7
6.20 No Pets 58
6.21 Security 58
6.22 Noise 58
6.23 No Smoking 58
6.24 No Firearms 58
6.25 Alcohol/Drugs 58
6.26 Construction Personnel Conduct 58
APPENDIX
APPENDIX A
Definitions 5-61
APPENDIX B
Roof Form Table 62
APPENDIX C
Approved Plant List 63-66
APPENDIX D
Prohibited Plant Materials 67
APPENDIX E
Governing Regulations 68
APPENDIX F
Lot Survey Requirements 69
APPENDIX G
Design Review Application Forms 70-71
APPENDIX H
Illustrations and Photos 72
8
CHAPTER ONE
CANYON VIEW ESTATES AT IRONWOOD
COUNTRY CLUB DESIGN PHILOSOPHY
1.1 AN INTRODUCTION TO THE CANYON VIEW
ESTATES
The Canyon View Estates Community was created to afford its residents the opportunity
to experience a true desert retreat - relaxed, secluded, outdoor oriented and surrounded by
friends and family with whom to share the experience. At Canyon View Estates,
buildings and landscapes combine to reflect the informal, easy lifestyle and desert climate
of the Coachella Valley. This design philosophy is based on three main objectives:
Establish a way of building and landscaping that utilizes the desert climate to
create homes that are effortlessly “connected” to the land. The desert lifestyle is
about living in a civilized landscape with few barriers. Mountain and desert
views, breezes and sun orientation provide the framework for creating living
environments that blur the conventional distinction between inside and outside.
Create homes that respond to the desert’s climate and setting by drawing upon
historic building traditions and utilize native or natural materials. Accordingly,
architectural designs that provide proper solar orientation, create areas of shade
and natural ventilation are encouraged.
Create a lush desert landscape throughout Canyon View Estates that embraces,
dominates and unifies buildings. Landscape design at Canyon View Estates
emphasizes establishing appropriate desert and ornamental plantings throughout
the Community so that the landscape becomes the dominant element. Plantings
will be used as an integral part of the building by framing and/or buffering views,
defining gardens and outdoor living spaces and providing shade and privacy.
1.2 THE NEIGHBORHOOD PLAN
Canyon View Estates’ Neighborhood Plan has been carefully crafted to create living
environments that enhance modern lifestyles. Accordingly, these Guidelines have been
written to support the following Neighborhood design objectives:
View Sheds
Protecting and enhancing mountain and desert floor views for residents from their homes
and/or throughout the Community as a whole is a primary goal of these Guidelines. To this
end, several types of view sheds are identified. Special provisions within these Guidelines
and the review procedure were established to ensure their protection.
9
Short Range Views are generally of golf and/or water features. Building
envelopes, landscaping provisions and grading concepts are described in these
Guidelines to maximize views of these amenities.
Mid Range Views of the Santa Rosa Mountains and Eisenhower Peak are the
most dramatic and form the signature visual image of Canyon View Estates.
Homeowners are encouraged to design homes and landscapes that embrace
these view opportunities.
Long Range Views of the Chocolate Mountains or distant Coachella Valley
floor are most dramatic at sunrise and sunset. View angles of the valley floor
are generally quite low, so landscaping or buildings must be designed with this
in mind.
Views from Golf - An important community asset is the view shed from the
golf course. Designers are urged to consider this in their concept design. The
objective is that the home is not a focal point and that it rests discreetly within
the landscape.
In all cases, view preservation will be a primary criteria by which the Canyon View
Estates DRC will evaluate applications. Landscaping or other improvements that
adversely affect views from another Lot or Common Areas will not be allowed,
regardless of whether or not the proposed or constructed improvement conforms to
these Design Guidelines.
Privacy
The Neighborhood Plan employs several planning mechanisms to create privacy:
Slightly elevating the Lot pads above the road to create a subtle sense of separation
between the semi-private front yards and the more “public” street.
Densely landscaped desert washes at the entry and between several Lots to convey a
feeling of neighborhood exclusivity and site separation.
Larger side yard setbacks that will allow greater separation between buildings and create
the opportunity to achieve privacy through the use of dense landscaping.
Privacy between homes as an important element to creating a secluded desert retreat.
Dense landscaping and walls are allowed under the Guidelines to achieve this goal.
10
CHAPTER TWO
SITE AND LANDSCAPE GUIDELINES
The following chapter outlines Guidelines and standards for all site work relating to the Homesite,
including grading, planting, siting of structures, design of outdoor areas and preservation and
enhancement of the surrounding landscape.
2.1 SITE AND LANDSCAPE OBJECTIVES
Design Objectives
The following are the main objectives for landscape and site design at Canyon View Estates:
To create landscapes that are appropriate to the desert and reinforce the architectural
image.
To build upon the developer installed landscape in a manner that creates a unique setting
for each Homesite.
To encourage landscape designs for homes along the golf course that create a seamless
transition from the golf course landscape and Common Areas to more intimate landscapes
of the Homeowner’s private gardens.
To create outdoor spaces that are natural extensions of the indoor spaces.
To design outdoor spaces that ameliorate the climate by providing shade, shadow, texture
and capturing breezes.
To utilize plants, landscape structures and details that draw upon the region’s heritage and
respond to the unique climate and setting.
To utilize plant palettes that are sensitive to water conservation, recognizing that this is not
only responsible but also responds to an emerging trend in the design of desert
communities evident in local regulations.
o protecting and enhancing the desert landscape;
o preserving the dominance of the natural or introduced landscape by siting buildings
where they will blend into the site.
Each Lot Diagram consists of:
The Building Envelope - is that portion of the Lot where all Improvements must take place. The
Building Envelope consists of a Private Area where buildings, other vertical structures and
landscape Improvements may occur and a Transition Area where only landscape or horizontal
Improvements (patios, pools, paths, etc.) may occur. The Building Envelope is more fully
described in Section 2-3.
The Natural Area - is that portion of the Lot that lies outside of the Building Envelope and is to be
landscaped or left as undisturbed desert. Portions of The Natural Area may have been landscaped
by the Developers as part of the golf course, slope areas or streetscape. It is the intent that these
landscaped areas are preserved or enhanced and the Homeowner landscapes are blended into the
golf course, slope or streetscape planting concept.
11
2.2 LOT DIAGRAMS
A Lot Diagram has been prepared for each Lot which describes the unique attributes of that Lot
and indicates important design parameters such as, but not limited to: Building Envelope areas,
planting accent areas, easem*nt areas, special restrictions and suggested driveway access.
Lot numbers and layout are designated on the Neighborhood Plan and Lot Diagrams that
correspond to the Plan are available at the Association Office. Building Envelope locations were
determined based on the specific characteristics of each Lot and on the planning and design
objectives for Canyon View Estates, specifically:
maximizing privacy;
maximizing short and long range views;
minimizing grading, only allowing the lowering of pad elevation a maximum of 2- feet;
protecting and enhancing the desert landscape;
preserving the dominance of the natural or introduced landscape by siting buildings where
they will blend into the site
2.3 BUILDING ENVELOPES
Building Envelopes have been established for all Lot Diagrams to ensure that every home is sited
to maximize mountain and valley views, minimize impacts to the site, maintain the privacy of
adjacent Lots and maintain views from the golf course to preserve the existing golf experience.
Building Envelopes are areas designated on the Lot Diagrams within which all Improvements on
the Lot (except utility connections, some landscape, drainage work and driveways) must take place.
Building Envelopes comply with city setback criteria and respond to natural features such as
topography and view orientation. Creative site planning and architectural design solutions that do
not parallel or delineate property or setback lines are encouraged. The DRC will consider, on a case
by case basis, adjustments to the Building Envelope if the benefits of such an adjustment to the
Homeowners and Canyon View Estates are demonstrated.
Digital base plan files indicating property lines, topographic information, Lot Diagrams and utility
information are available from the Canyon View Estates Development Office. These are offered
only as a convenience to owners and their design team and are not a substitute for a certified
survey. Owners are strongly encouraged to obtain a certified survey prior to beginning design
work.
The Building Envelope is made up of two areas, the Private Area and the Transition Area, as
described below.
2.3.1 PRIVATE AREA
The Private Area is that portion of the Building Envelope which includes buildings and outdoor
private spaces. The buildings within the Private Area must conform to the maximum Building
Height requirements set forth in these Guidelines and as indicated on the Lot Diagrams. Most of
the landscape within this area is not visible from neighboring Lots, the golf course or the street
12
because it is screened by privacy walls, buildings and/or other landscape elements.
Within this area, the Owner has more flexibility in creating a more ornamental and personal
landscape. All plant materials must be selected from the Approved Plant List in Appendix C and be
in accordance with any applicable regulations, including those of the City of Palm Desert or the
Coachella Valley Water District.
2.3.2 TRANSITION AREA
The Transition Area is located within the Building Envelope and is visible from the golf course,
Common Areas, streets and neighboring Lots and is adjacent to the Natural Area.
No vertical structures may be located in the Transition Area. Pools, low retaining walls and/or
freestanding walls (maximum of 3 feet height in rear transition areas, maximum 5 feet height in
front/street transition areas, and a maximum 6 feet height in side yard transition areas), patios, spas,
outdoor barbecues, new plantings or other horizontal landscape Improvements shall be allowed.
Landscape structures (such as trellises and/or arbors etc.) and walls higher than those described
above or landscape that has the potential to block views are prohibited. Privacy walls and utility
screening walls to a maximum of 6 feet height along the side property line or located within the
side yards may be allowed at the discrimination of the DRC.
2.4 THE NATURAL AREA
The Natural Area is that portion of the Lot that lies outside the Building Envelope and must be
landscaped in accordance with these Guidelines. Minimal grading for driveway access, utilities and
to accommodate drainage is allowed within the Natural Area. In some cases, the Developer has
landscaped portions of the Natural Area on individual Lots and has established a maintenance
easem*nt to maintain this landscape. This existing landscape must be protected and Designers are
encouraged to extend this landscape up to and/or into the Transition Area of the Building
Envelope.
2.5 COMBINING LOTS
In cases where the Owner owns two or more contiguous Lots and wants to combine two or more
Lots into a single Lot, the Owner must receive the consent of the City of Palm Desert and the DRC.
A revised Building Envelope will be prepared by the DRC with input from the Owner and their
Consultants. The total dimension of the side yard setback of the revised building envelope will be
equal to or greater than the sum of the side yard setbacks of the uncombined Lots. Additionally, the
new Building Envelope area resulting from combining the Lots shall not exceed the sum of the
Building Envelope areas of the uncombined Lots. The revised Building Envelope shall be approved
by the DRC prior to submitting the preliminary submittal to the City of Palm Desert. Following
approval by the DRC, any required regulatory approvals will be the responsibility of the Owner.
The DRC will carefully review issues relating to Building Mass and scale when reviewing a home
on combined Lots. Homeowners and their design team are encouraged to be sensitive to these
important issues when preparing their applications.
13
2.6 BUILDING COVERAGE AND MINIMUM FLOOR AREA
In no case shall Building Coverage, exclusive of driveways, decks, balconies, or overhangs, exceed
35% of the total Lot area. Minimum Floor Areas for interior air-conditioned space will be 3,000
square feet. Though there are no maximum Floor Area requirements, the DRC will be reviewing
applications to ensure that all Improvements are appropriately scaled to the Lot and surrounding
Landscape. For Floor Area and Building Coverage definitions, refer to Appendix A – Definitions.
2.7 GRADING AND DRAINAGE
Objectives
To blend new Lot Improvements with adjacent Common Area or slope grading or golf
course landforms.
To ensure drainage Improvements are compatible with adjacent Lots or landforms.
To create appropriate landforms as a setting for the building Improvements.
Grading Guidelines
All cuts, fills and retaining walls must create smooth transitions at top and bottom of slopes
and appear to be extensions of natural landforms. In general, finished slopes shall mimic the
gently rolling topography of the golf course or natural desert. Long, straight landforms shall
be avoided, while rounded flowing forms are encouraged.
Building Pad elevations may not be raised, but they may be lowered a maximum of 2-feet
to provide better views to foreground landscape and the golf course. Changes in pad
elevation must be approved by the City of Palm Desert and it is the Owner’s responsibility
to obtain this approval prior to Final Design Review.
If the Building Pad elevation is lowered, the Building Height elevation shall be determined
from the new lowered Building Pad elevation for those portions of the building located on
the new lowered pad.
Grading operations shall not cause any on or off site erosion, even during construction.
Grading at the outer edges of individual Lots shall not result in abrupt transitions to
adjacent landforms, Lots or streets.
Slopes shall not exceed 3:1 unless it can be demonstrated that a steeper slope will result in a
more appropriate design solution. When 3:1 slopes are used, their visibility shall be
minimized and have a landscape treatment that helps mitigate the abrupt visual character of
the slope. Contour grading is to be used instead of structures wherever feasible.
In general, all grading shall be completed within the Building Envelope and shall not
impose offsite drainage onto adjacent Lots.
Cut and fill slopes are to be landscaped and restored with plant materials that blend with the
surrounding landscapes. Landscaping of these slopes shall be completed as soon as possible
and erosion control measures shall be implemented upon completion of grading.
In general, cut and fill quantities from grading operations shall balance on site.
In general, grading within Association Easem*nts areas that are part of the golf course
landscape is prohibited with the exception of minor “tie-in” grading.
14
2.7.1 RETAINING WALL GUIDELINES
The maximum height of retaining walls within the Private Area is 6-feet as measured from
the lowest finished grade level to the top of the wall. The maximum height for walls within
the Transition Area is 3-feet, unless the wall is a side yard privacy wall, utility enclosure
wall or auto court screening wall. Retaining walls include any wall that retains earth 2-feet
or more in depth. Retaining walls shall be built to extend and/or blend with the existing
topography.
Where grade changes exceed 6-feet, stepped-back or terraced wall structures with planting
terraces (4-feet minimum width) are to be used. In extraordinary circ*mstances, higher
retaining wall heights may be allowed if it can be demonstrated that such a solution has no
adverse impact to neighboring Lots or Common Areas and it causes less disturbance to
existing topography or landscaping.
Acceptable materials for retaining walls include integral colored stucco, adobe and/or stone.
If stone is used, a dry stack pattern, structural in appearance, is required. Thin stone veneers
that are not structural in appearance are unacceptable. Masonry block with stucco, real
stone, and stone veneer is acceptable.
Stone or stone-faced walls are to be designed with a 1:12 batter if the overall wall height
exceeds 3-feet.
The tops of walls are to be shaped to blend with natural contours. Ends of walls shall not be
abrupt, but are to be designed to create natural-looking transitions with the existing
landforms and vegetation.
In general, retaining walls facing the golf course, street or other Common Areas may not
delineate or parallel Building Envelope boundaries or property lines for more than a 25-foot
long distance without a vertical or horizontal offset. Walls are to utilize multiple vertical
and horizontal offsets that step with the site’s topography and house design. All walls shall
utilize a minimum vertical offset of 8-inches and a minimum horizontal offset of 16-inches.
The horizontal separation between vertical offsets shall be a minimum of 24-inches.
Exceptions may be granted by the DRC if the DRC determines that such offsets are
aesthetically less desirable in the context of a particular submittal. Retaining walls along
stairs are excluded from these Guidelines.
2.7.2 DRAINAGE GUIDELINES
In general, increased water flows on Lots shall be detained on-site and directed into
improved channels that detain water and encourage percolation. The historical entry and
exit of water and flow rate on a Lot must be maintained. Drainage from impervious surfaces
may not be directly dispersed into natural wash areas. Every effort shall be made to
maintain and not to increase the amount of the historic water flow in exiting washes.
No changes shall be made to the natural or existing drainage patterns on any Lot that could
cause an adverse effect upon another Owner. No cross Lot drainage is allowed.
Drainage design shall reduce erosion, runoff, and adverse impacts to water quality.
Improved channels or drainage Improvements are to be designed to appear and function like
natural drainage ways.
Materials and sizes for all culverts, visible drainage structures and driveways are to be
approved by the DRC. Concrete culverts shall be utilized rather than metal or plastic. The
ends of culverts shall be blended into the landscape by utilizing boulders, planting and/or
15
painting the interior of the culvert black.
When appropriate, gutters and downspouts will direct drainage from the roofs to on-site
drainage collection areas. In no event shall gutters and/or downspouts drain onto adjoining
Lots.
Lots 50-52 must retain all storm water on site.
In general, when utilizing rip-rap treatments for erosion control the following Guidelines
shall be followed to create a more natural looking drainage way:
o Stone may only be used in a color which is natural looking and blends with the
desert.
o Utilize stones that are a variety of shapes and sizes and are indigenous to the area.
Rounded stones (such as river rock) may not be used.
o Locate splash bowl or stone splash block at downspout or scupper locations to
dissipate the energy of the water.
o Slopes shall not look “engineered” or abrupt. Drainage ways or rip-rap areas shall
be further blended into the topography by covering the rock with 6- inches of native
soil and revegetated.
o Alignments of rip-rap treatments shall utilize meandering rather than straight
alignments and slowly “bleed” out to the desert by utilizing bigger spaces between
stones and smaller stones on the edges.
2.8 DRIVEWAYS AND AUTO COURTS
Objectives
To minimize visibility of paved areas from neighboring Lots through careful siting, grading,
design, use of architectural devices and landscape.
To blend driveways into the natural terrain so that grading is minimized.
To create “auto courts” for parking and garage areas through the use of special paving,
architectural devices, plantings and/or walls.
To minimize the quantity of paving in front setback or Transition areas.
Guidelines
All driveways are to follow alignments that minimize grading or other disruption to the site.
The driveway-parking-garage layouts are to minimize the visibility of the garage doors,
driveways and off-street parking from the street, Common Areas and adjoining Lots.
One driveway entry will be permitted for Lots that have a street frontage of 115 feet or less
at the edge of pavement. A second driveway entry for Lots that have a street frontage
greater than 115 feet at the edge of pavement may be approved by the DRC provided that
neither driveway entrance is closer than 15 feet to the property line and the second entry has
no impact on neighboring Lots or Common Areas. A suggested driveway access point is
indicated on the Lot Diagram. Alternate locations may be approved by the DRC if the
applicant demonstrates that such a relocation furthers the objectives of the Canyon View
Estates.
Approved materials for driveways and auto courts include colored and/or patterned
concrete, precast concrete pavers, stone, brick, cobble, and/or decomposed granite with or
without concrete and/or stone, cobble or brick edge detailing. Asphalt may not be used for
driveways with the exception of shared driveways.
16
Coloring and texturing of concrete is required. Colors of finish paving materials shall
complement proposed buildings and integrate well with the surrounding earth tone colors.
No smooth or broom finishes will be allowed (only seeded or washed, exposed textures).
Driveway paving shall match or be similar in style and/or color to paving used for other
outdoor areas such as terraces and/or stairs.
Maximum gradients on driveways shall be 12% or as directed by Fire Department
regulations.
Driveways shall be a maximum of 15-feet wide, except at the driveway apron to garage
entrances and/or where they provide a turnaround at a garage and/or guest parking. Parking
and turnaround areas are encouraged to be located within the Building Envelope and
comply with all applicable Fire Department requirements.
The quantity of hardscape in the auto court shall provide ample space for easy turning
movements and vehicular parking. Excessive paving that impacts the surrounding landscape
areas is discouraged.
Lots 50-52 will gain access from a shared drive and the developer will construct the
common segment of the driveway and provide utilities to the Lot line of all Lots serviced
by the common driveway. Homeowners gaining access from the shared driveway shall be
responsible for maintenance.
2.9 GARAGES AND PARKING
Objectives
To minimize visibility of parking areas through planting, architectural projections and
careful siting of garages.
To accommodate all parking needs for the Residence on the Lot.
Guidelines
All Lots shall include an enclosed garage that can accommodate a minimum of two cars.
Guest parking - Each Lot shall contain a minimum of two additional guest parking spaces
(in addition to the required two enclosed spaces). Unenclosed spaces must utilize a
combination of plantings and/or low walls (a maximum of 5-feet) to screen cars from view.
All guest parking areas and garages shall occur within the Building Envelope.
Vehicular parking spaces shall have a minimum dimension of 9-feet by 20-feet.
Garages must be sited and located so that visibility from the street is minimized. Side entry
and/or angled entry garages are required. Separating a three-car garage into two masses
(one single car and one two car garage) is strongly encouraged.
Recessed (minimum of 12-inches) garage doors and single stall door openings are required.
Carports may be approved when designed as an integral feature of the overall design of the
home. Carports that appear to be tacked on and/or constructed with thin column supports
and thin-banded fascias will not be approved.
In no case shall a three or more car garage face the street.
Limited on street parking is permitted to provide for temporary overflow/guest parking. No
permanent on-street parking for Homeowner’s vehicles is permitted.
On-Lot parking of boats, trailers, RVs or similar types of secondary recreational vehicles is
prohibited.
17
2.10 COURTYARDS, TERRACES, PATHS AND OUTDOOR
STAIRS
Objectives
To create outdoor spaces that ameliorate the climate through the use of plantings, walls,
architectural devices and/or landscape structures.
To utilize materials that complement the architecture and materials of the building.
To create outdoor “rooms” which are natural extensions of the indoor rooms of the
Residence.
Guidelines
The spatial organization of the Residence as well as the organization of the outdoor spaces
is to be designed as one unified whole. The demarcation line between indoors and outdoors
is to be blurred.
All paths, outdoor stairs and terraces are to be located within the Building Envelope.
The use of natural materials such as stone, tile and/or decomposed granite is encouraged.
Concrete may be used provided it is colored and textured to complement the Residence.
Extending flooring materials from the inside of the Residence to the outdoor spaces is
encouraged.
The use of architectural devices such as courtyards, arcades, trellises and/or porches to help
create a gradual transition from indoors to outdoors is strongly encouraged.
Designs shall minimize the use of several different types of paving materials in order to
produce an understated, unified design.
2.11 WALLS, FENCES AND GATES
Objectives
To construct walls, fences and gates which borrow from the regional building traditions.
To design walls, fences and gates that are related to and are natural extensions of the
buildings.
To achieve privacy through berming, low walls and careful building and planting design,
thereby minimizing the need for higher privacy walls and fences.
All wall designs and layout approvals will be at the discretion of the Design Review
Committee.
Guidelines
Walls, in general, shall be a maximum height of 6-feet. It is encouraged that wall heights
are as low as possible to achieve privacy and preserve views and the visual character of the
desert. Wall designs shall be extensions of the architecture of the building.
Walls shall not define property lines and/or Building Envelopes. Privacy walls and screen
walls located in side yards are to be used only where landscape solutions will not provide
adequate privacy. Low walls and landscape may be used to define Private Areas of the Lot.
Walls shall occur inside property lines unless contiguous Owners agree on design and cost
sharing.
18
On the golf course side of the Lot, privacy walls and fences shall not be
constructed in the rear Transition Area . See-through fences, low hedges or low
walls may be allowed in this area at a maximum height of two (2) feet with a minimum
setback of five (5) feet from the rear property line and must be screened from view. As a
note, this condition may create a need for coordination with the neighbor(s) or placement of
the wall at an appropriate distance from the property line to allow for landscape screening
on both sides of the wall.
Ends of walls must incorporate decorative terminus details and not end abruptly.
Approved wall materials include plaster or stucco finishes, adobe, architectural concrete,
and/or stone. The minimum thickness of walls shall be 6-inches. In addition, ornamental
iron and/or decorative tiles may be incorporated into wall designs provided it is related to
the architecture of the Residence and the regional vernacular.
Site walls that are visible from the golf course, street or Common Areas shall incorporate
multiple offsets and variation in the vertical heights to avoid long straight lines of
landscape.
Vinyl clad cyclone, and/or open grid metal fencing will not be permitted.
“View” fences are encouraged to preserve the openness of the desert landscape. These
fences may utilize an open metal picket or designs which are, in general, “see-through” and
frame rather than block views of the desert landscape beyond.
Wall and fence designs shall be designed to be compatible with walls and fences on
adjacent Lots and/or Common Areas. If existing walls/fences exist that abut the applicant’s
property, these must be shown on the applicant’s survey, site and landscape plans.
Vehicle entry gates and/or entry columns shall be set back from the curb line a minimum of
30 feet and be located within the Building Envelope. Gates and columns shall be designed
in an understated way and not make a design statement when viewed from the street,
Common Areas or neighboring Lots.
Pool security fencing shall meet the requirements of the City of Palm Desert. Utilizing
grade changes in conjunction with fencing to meet these requirements is encouraged.
Fencing along the golf course boundary is strongly discouraged. Fencing along the golf
course boundary that creates an overly strong demarcation between the golf course
landscape and the Homeowner landscape is prohibited.
2.12 LANDSCAPE STRUCTURES
Objectives
To design landscape structures that appear as extensions and/or additional building
components of the main Residence.
To incorporate landscape structures which help to ameliorate the climate and create shade,
shadow and texture.
To create a “ceiling” plane for outdoor spaces.
Guidelines
Landscape structures such as arbors, porches, greenhouses and/or decks must be located
within the Private Area of the Building Envelope.
The height, color, materials and style used for outdoor structures are to be the same or
19
similar to the Residence. Heavy wood timbers, if used for rafters, posts or trellis elements,
must be substantial in dimension and treated with stain or paint to withstand the effects of
climate.
Landscape structures are to be visually subordinate to the main Residence. Accordingly, the
height and visual mass of an outdoor structure shall be substantially less than that of the
main Residence.
In general, the same Guidelines that apply to architecture apply to the design of the
landscape structures.
2.13 PLANTING
Objectives
To establish a gradual landscape transition from the more intensive landscape areas around
the building to the golf course or Common Areas.
To assist in melding buildings with the site.
To utilize plant materials to define outdoor rooms, frame views, create privacy and/or
provide landscape focal points.
To utilize landscape techniques and plant materials that are sensitive to water conversation.
To utilize appropriate plant materials and designs that maintain views from adjacent Lots or
Common Areas.
2.13.1 GENERAL PLANTING GUIDELINES
In general, the planting design of the Lot shall take its cue from the adjacent existing natural
desert, golf course or Common Area landscape.
Plant materials are to be used to help to complete structures and provide shade, texture or a
focal point for outdoor rooms. Shrubs may be used as informal low walls and trees may be
used to provide scale for building masses.
An Approved Plant List which lists indigenous and ornamental plant materials is located in
Appendix B. This list indicates which areas (Private, Transition or Natural Area) of the Lot
a plant is best suited. In general, species used in the golf course are to be integral to the
overall landscape design and not just limited to Natural and Transition Areas.
Proposed landscape plantings that are not on the Approved Plant List shall be identified on
all landscape submissions with a full description of the plant and why it is proposed for use.
The DRC reserves the right to disapprove of any plant they find incompatible with the
overall design intent.
The landscape design on each Lot shall gradually transition from the Private Area as the
most intensive landscape to the Natural Area as a more natural landscape. The Private Area
shall be separated from the Natural Area either by the Transition Area or by walls,
courtyards and/or other structures.
In order to facilitate DRC review of how the proposed landscape will transition to the
Natural Area or golf course, the proposed landscape plan will show all 5 gallon and larger
plant material located in the Natural Area within 20 feet of the property line on all adjacent
Common Areas or the golf course. See Chapter 5 for a detailed description of submittal
requirements.
Surface-select decomposed granite boulders may be used in the landscape if appropriate to
20
the particular site and setting. They shall be sunk a minimum of one-third (1/3) below
grade, utilize a variety of sizes, and be massed in groupings of two or more to appear as
natural rock outcrops. Permeon or other artificial painting or staining may be required by
the DRC.
All trees, shrubs, and ground covers must be maintained properly. All dead or dying plants
shall be replaced promptly. Maintenance for seasonal planting will be required in the off-
season to remove all dead or frost damaged growth, leaf litter or other debris. Irrigation
systems must be maintained to ensure survivability of plant material.
A more informal, natural planting design shall be used in the Transition and Natural Areas
to create a gradual transition from the golf course landscape to the Private Area landscapes.
The use of decomposed granite is allowed in private courtyard areas and side yards
screened from public and neighborly view. The soil throughout the property should have a
natural appearance. Gravel, rocks, cobble, pebbles and decomposed granite may be utilized
to cover exposed dirt in some planter areas; however, they may not be utilized to cover the
native soil throughout the entire front and rear yards. Coverage of native soil may not
exceed 45% in either the front or rear yard(s). Rocks and cobble must be of a consistent
size and color and cannot extend all the way to the property lines within the front or rear
Transition Areas or within any Natural Areas (except where completely screened from
view). Where decomposed granite, rocks, cobble, etc. are proposed actual samples will be
required for review and approval. When selecting groundcover materials smooth rock
should be avoided. Irregular rock and cobble should be utilized in colors that are consistent
with the soil and the architectural style of the home.
Areas that have been previously landscaped by the Developer shall be protected from
damage during construction. Any damage to previously landscaped areas by the
Homeowner’s Contractor shall be promptly replaced with plant materials of the same size,
quantity and species.
A prohibited plant list is included in Appendix D. These plants represent species with
characteristics that are potentially destructive to the native desert landscape, have weed-like
tendencies or are in conflict with the intent of these Guidelines. Under no circ*mstances
may a plant from the prohibited plant list be used.
Turf, or artificial turf, shall be contained by permanent edging or mowing strip to
provide a clean appearance. To maximize the cooling effects of turf and minimize
water consumption all turf areas should be located within the Private Area adjacent
to or near the house and accessible from patio areas or outdoor rooms. Artificial
turf will not be allowed in the Transition Areas, Natural Areas or where adjacent
to existing natural grass. Specifications are required for consideration by the
committee for all artificial turf, including installation methods, quality of turf,
color, manufacturer, etc. A sample of the proposed turf is required for review.
The Transition and Natural Areas are typically defined on the Lot Diagrams as
the area between the curb and the front building setback line.
To create a more natural looking desert landscape character in the Natural and Transition
Areas, the use of multi-trunked trees is preferable over the use of nursery “standards” in the
landscape design.
All plant material shall meet the requirements of the “American Standards for Nursery
Stock-ANSI 260.1”
21
2.13.2 PRIVATE AND TRANSITION AREA PLANTING GUIDELINES
A larger variety of plant material, including non- native species, may be used in the Private Area
and Transition Areas. The Private Area is that area of the Lot defined by walls, Buildings,
landscape structures and/or plant materials visible from public areas, including adjoining Lots, golf
course and/or Common Areas.
The use of trees is preferred in areas close to the house to help blend buildings with the site,
accentuate entry areas, provide for climate amelioration, and help to define outdoor spaces.
Tree and Shrub Planting Requirements within Private & Transition Areas: In order to blend
buildings with the site the following plant materials shall be planted within Private &
Transition Areas. The DRC may require additional tree planting on a Lot if, in their
opinion, the Lot size, building siting, mass or character, or any other circ*mstance specific
to that Lot, warrants an increase in tree size or density.
o Five canopy trees, 48-inch box minimum.
o Ten shrubs (five-gallon minimum size) per 500 s.f. of building area. Building area
shall be rounded up to the nearest 500 s.f. to calculate the number of required
shrubs.
2.13.3 THE NATURAL AREA PLANTING GUIDELINES
The Natural Area shall be planted with the more indigenous plant palette of the golf course,
streetscape or Common Areas in a similar pattern and density so as to create a gradual transition
between the Homeowner landscape and Community landscape.
Plantings are to slowly transition from the more intensively landscaped areas of the Private and
Transition Areas to the “recreated” or native desert landscape of the Natural Area. These areas
shall be maintained so that they resemble the more natural golf course or Common Area landscape.
A low wall that separates the Private and Transition Areas from these areas may also be used.
The placement and groupings of shrubs, ground covers and trees shall be naturalistic and
random and not formal or straight. Owners and their consultants are to study the existing
landscape in adjoining areas for grouping and spacing characteristics.
Ornamental grasses that match those used on the golf course are encouraged.
Plant material within the Natural Area shall be located to not block oblique views from
adjacent Lots.
Multi-trunked trees are required for all trees planted in the Natural Area.
Tree and Shrub Planting Requirements within Natural Areas: In order to blend buildings
with the site the following plant materials shall be planted within Natural Areas. The DRC
may require additional tree planting on a Lot if, in their opinion, the Lot size, building
position, mass or character, or any other circ*mstance specific to that Lot, warrants an
increase in tree size or density.
o Ten shrubs (five-gallon minimum size) per 500 s.f. of building area. Building area
shall be rounded up to the nearest 500 s.f. to calculate the number of required
shrubs.
22
2.13.4 EXISTING STREETSCAPE AND LANDSCAPE ON LOTS
The Developer has installed landscape along streets, drainages and slopes. In some cases, this
landscape is within the Lots. This vegetation shall not be removed, except for driveways, utility
connections and minor grade tie-ins and shall be incorporated into the overall design of the Lot.
The streetscape and any landscaping installed within the Lot by the developer will be irrigated by a
system connected to the domestic water system or by water purchased from the golf course. The
Owner is required to assume responsibility for the watering of all landscaping within the Owner’s
Lot upon closing. Responsibility shall mean an apportionment of the expenses among all Owners
whose Lots remain undeveloped and landscaped. In addition, the Owner will be assessed a monthly
maintenance fee by the Association separate and apart from the HOA dues.
2.14 POOLS AND WATER FEATURES
Objectives
To locate pools and/or water features where they are not highly visible from public areas.
To design pools and water features which augment the outdoor spaces and extend the
architectural style of the main buildings.
Guidelines
Cultures that developed in arid regions historically have treated water as a precious resource.
Traditionally, this meant water sources were “protected” within enclosed courtyards, water
movement was kept to a minimum to reduce evaporation and basins or “canals” were simple,
geometric shapes, articulating arrival to an “oasis.”
Pools, spas, ponds and other artificial water features must be built within the designated
Building Envelope and set back a minimum of five (5) feet from the property line. Small
water features located on side yard privacy walls may be exempt from this guideline if the
applicant can demonstrate the water feature will not have a noise or visual impact on the
adjacent Lot. Pools and spas in the rear transition areas may be allowed closer than 5’ to the
property line if it is demonstrated that such Improvements have no impact on the golf
course, Common Areas, or adjacent Lots.
In general, pools and water features are to be designed to be integral parts of the residential
design and visually blend with the landscape. Landscaping should be selected and arranged
to complement the water feature and create “outdoor rooms.”
Swimming pool and spa areas must be screened with low landscape walls and/or plantings
to minimize their visibility from any Natural Areas, streets or the golf course. Swimming
pools and spas, and the doors and gates leading to them, must be constructed in accordance
with the regulations of the City of Palm Desert, including fence and enclosure heights. Pool
enclosures shall utilize a combination of fencing and grade changes to meet wall
requirements set forth by the City and these Design Guidelines.
Mechanical equipment must not be visible or heard from adjacent Lots and shall be located
below grade or enclosed by walls or other suitably effective screening methods.
The exposed edges of infinity or “negative” edge pools must utilize an approved natural
stone or shall be a dark color and blend with the adjacent landscape. Exposed pool walls or
surfaces that are visible from off site must be screened with landscape/plantings.
23
2.15 IRRIGATION
Objectives
To minimize the amount of landscape irrigation through a water sensitive landscape design.
To utilize irrigation systems that provide efficient water coverage and minimize water
usage and runoff.
To ensure adequate levels of irrigation using automated systems to promote optimal plant
growth and establishment of a mature landscape.
Guidelines
All landscaped areas within the Lot must be irrigated. The use of drought tolerant plants
combined with minimal irrigation must be the basis of all landscape submittals. The use of
automatic underground drip irrigation systems will be required in most landscape areas to
ensure the establishment and sustain- ability of the landscape.
Group plant materials according to their water consumption needs.
All irrigation systems will utilize an automatic, programmable controller to maximize
The irrigation system must be designed and installed to preclude over spray or runoff into
the Natural Area or onto adjacent pavements or walls.
2.16 LIGHTING
Objectives
To preserve the nighttime dark sky by minimizing the amount of exterior lighting.
To utilize low intensity, indirect light sources to the extent required for safety and subtle
drama.
To utilize light fixtures which complement the architecture and enhance the landscape.
Guidelines
Exterior building lighting, either attached to or as part of the building, shall be the minimum
needed to provide for general illumination, safety, and security of entries, patios and
outdoor spaces and associated landscape structures.
Exterior site lighting must be directed onto vegetation or prominent site feature and not
upon the building.
Lighting of plant materials shall be achieved with hidden light sources and down lights
from above.
To preserve the dark sky, uplighting shall be minimized. A maximum of ten (10) trees,
palms or other large plant species may be lit in total.
Only low voltage lighting, with a maximum of 25 watts may be used for all exterior site
lighting applications. Line voltage may be used for lights on the building but must be
lamped with 25 watt maximum incandescent bulbs.
Owners are encouraged to install underwater pool, spa and water feature lights with reostats
so that they may be easily dimmed if it is determined that spillover light from these sources
is a nuisance to neighboring Lots/Common Areas or is adversely affecting the nighttime
dark sky.
24
To preserve the nighttime dark sky, lighting emanating from the home’s interior should be
carefully considered. Interior light shall be concentrated at activity areas and minimized
next to windows. Built-in lighting adjacent to windows shall be directed towards the
home’s interior. Architectural or decorative elements shall be used to minimize the quantity
of light escaping through the windows. The maximum level of foot candles 20-feet from a
window shall be 0.01- foot candles.
With the exception of low-level driveway lights, all lighting must occur within the Building
Envelope. Subtle lighting of the driveway entry and/or address numbers is allowed. A string
of driveway lights clearly defining the drive alignment will not be allowed. A minimal
amount of shielded lighting may be allowed on a case-by-case basis not to exceed 25 watts
(or LED equivalent).
Light fixtures should be located and designed to avoid spillover onto adjacent Lots.
Security lighting may be installed on buildings provided it does not create a light nuisance
to adjoining Lots, Common Areas or the golf course. All motion sensitive security lighting
must be on timers that automatically turn the lights off after 5 minutes. Motion detectors
should be located to avoid accidental triggering by wildlife or wind- blown vegetation.
Soffit lights over garage doors are allowed if they are an accent light that does not exceed
25-watts. Only one light per car space will be allowed.
The use of LED lighting will be allowed subject to strict architectural restrictions. In the
broadest sense, the intention is that all non-incandescent lighting (including Light Emitting
Diodes or “LED” and Compact Fluorescent Lights) are subject to the same restrictions as
incandescent lighting. The use of LED technology is encouraged and the lumen output is not to
exceed the equivalent of the light output of the low voltage MR-16 lamps or equivalent landscape
lamps not to exceed 50 watts per fixture. All lamps must be warm spectrum and replicate the light
“quality” of incandescent lamps. Recognizing that lighting technology is a rapidly evolving
technology alternatives will be considered on a case-by-case basis. Because these types of lights
are new, standards for determining their performance to the above listed criteria are not well
established. If you intend to submit a lighting plan that utilizes non-incandescent lights we
highly encourage you to submit your plan early and expect a few iterations as the DRC
works with you to make certain your lighting plan meets our required specifications. LED
Lighting must be consistent with the incandescent lighting with regard to lumens output.
No colored lighting will be allowed except during the holidays (as specified below).
Approval may be granted for special parties or events with seven (7) day prior notice to the
Association Manager.
String or strip lighting, large patio candles, insect control devices and other miscellaneous
objects that are illuminated are discouraged but may be allowed on a case-by-case basis. A
submittal to the Design Review Committee is required prior to installation.
Understated and tasteful holiday lighting and decorations that are of a quality befitting the
community are encouraged at Canyon View Estates. Colored lighting, static lights, laser
projector lights and luminaries installed in a subtle, non-excessive manner are acceptable.
Decorations and displays should not have a commercial appearance and should not be
overly bright, excessively large or intrusive to neighboring properties, the golf course or
common areas. Holiday decorations and lighting may be installed no earlier than
Thanksgiving and must be removed no later than January 15th
or as approved by the DRC.
Decorations for other holidays may be installed no more than two (2) weeks prior to the
holiday and removed within one (1) week after the holiday or as approved by the DRC.
25
2.17 EXTERIOR SERVICE AREAS
Objectives
To screen service areas from off-site views.
To ensure any noise or odors from trash or equipment are contained within the service
areas.
Guidelines
Trash disposal areas, outdoor work areas, mechanical equipment and outside equipment
(including antennae and satellite dishes) are to be completely screened from off-site views
by the use of architectural features or plant materials. Where feasible, these areas are to be
integrated into the main buildings.
Trash container storage areas must be located so that they are easily accessible to service
personnel and offensive odors are contained. These areas shall require gates and sealed
containers.
Pool, spa equipment and air conditioning units shall be located behind walls or in
underground vaults to contain noise. Solid noise absorbing covers for equipment may be
required after installation if it is discovered that noise emanating from the units is a
nuisance to adjoining Lots, Common Areas or the golf course.
2.18 MISCELLANEOUS SITE ELEMENTS
2.18.1 PATIO FURNITURE
Exterior storage of patio furniture and outdoor living accessories (barbeques, heaters, etc.) in areas
visible from off-site is allowed provided it meets the following requirements:
If stored uncovered, the furniture is stored in the same locations as if it were in use.
If stored with covers, the covers must be made from non-reflective material with dark, earth
tone colors. Patio furniture and umbrella colors are to utilize subdued colors when their
location is visible from other Residences, the golf course, or Common Areas. The DRC
reserves the right to reject any such items if it is deemed they are not consistent with the
intent of these Guidelines and the Community’s aesthetic objectives.
2.18.2 SCULPTURES AND ARTWORK
All sculptures and/or artwork visible from adjacent Residences or Common Areas must be
approved by the DRC prior to installation. No reflective materials or bright colors will be allowed
in areas visible from the golf course, Common Areas or adjacent Lots. The Final Design submittal
is to include detailed information on size, location, materials, colors, mounting details and lighting.
2.18.3 BARBEQUES, HEAT LAMPS AND MISTING SYSTEMS
Barbeques, heat lamps and misting systems are to be built into walls or the overhead structures and
be architecturally consistent with the Residence. All equipment that is visible from other
Residences or Common Areas shall be non-reflective and have muted coloration.
26
2.18.4 FLAGPOLES, ANTENNAE, AND SATELLITE DISHES
Antennae and satellite dishes are subject to special review by the DRC. If proposed, these items
must be hidden by walls and/or buildings from view. Freestanding flag poles are prohibited.
2.18.5 ADDRESS MARKERS AND MAILBOXES
Address markers should be utilized at each residence for identification purposes in the event of an emergency or guest arrival. Individual numerals should be utilized with external lighting only.
27
CHAPTER THREE
ARCHITECTURE GUIDELINES
The following architectural standards have been developed to achieve the environmental,
Neighborhood and aesthetic objectives for Canyon View Estates. The intent of these Guidelines is
to encourage a diversity of design solutions while at the same time producing a unified design
aesthetic for the Neighborhood.
3.1 ARCHITECTURAL DESIGN OBJECTIVES
Objectives
The following are the main objectives for architectural design at Canyon View Estates:
To create buildings appropriate to a casual, outdoor desert lifestyle.
To design buildings that seem to “grow out” of the site by responding to the climate,
landforms, landscape and site elements.
To create buildings which have a strong indoor/outdoor relationship.
To create buildings that, through their design, massing and materials, convey a sense of
timelessness, permanence and quality.
3.2 DESERT ARCHITECTURE
For many, a secluded desert retreat is an opportunity to “reconnect” with what is important in our
lives: family, friends, ourselves or the great outdoors. Traditionally, desert architecture has
provided that respite from the elements--the oasis--to allow that reconnection to occur. Using
indigenous materials, buildings become a part of the desert environment, resting gently on the land.
This effortless connection between shelter and the natural landscape that is the hallmark of
vernacular desert architecture is also the goal of the contemporary homes that will be built at
Canyon View Estates. Set within lush desert vegetation, these homes will be subtle architectural
responses to the desert climate, views and landforms. Designers are encouraged to create
innovative design solutions that are not overly stylized or make a statement.
Residences at Canyon View Estates will be designed with these basic principles and elements:
Simple, multi-level forms, horizontal masses that are punctuated using vertical elements.
Flat and/or low-pitched roofs.
Building masses that are organized to create outdoor “rooms” with a strong link from inside
to outside.
Building masses that are primarily room sized volumes.
An emphasis on wall compositions that dominate the design rather than roof forms.
Deeply recessed doors that open directly onto terraces, porches and/or courtyard spaces.
The predominant use of natural materials for the main structure of the Residence such as
stone, adobe, stucco, or wood.
The use of broad overhangs that create deep shade, continuous canopies and dramatic voids,
while providing protection from the sun and the weather.
28
The use of contemporary building techniques and details that draw upon the indigenous
building traditions of the region.
The use of hand-crafted decorative details that add a sense of quality and uniqueness to the
homes. Building Height measured vertically above existing natural terrain to the highest
sloping roof or parapet.
3.3 BUILDING HEIGHT
Objectives
To minimize the visual impact of all buildings and to ensure that they are subordinate to
and blend with the surrounding desert landscape.
To ensure that the view potential from each lot is preserved.
Building Height Measurement
The maximum Building Height shall be established by a plane measured vertically above the
certified pad elevation. The overall height shall be measured from the highest parapet framing or
plywood sub- roof ridge to certified pad elevation and/or the existing grade adjacent to the building
exterior directly below.
Building finished floor elevation (FFE) shall be measured from the certified pad after developer
grading is completed.
Building Height
Allowable Building Heights and roof form designation for each Lot are indicated on the Lot
Diagram and in Appendix B - Roof Form Table. In no case shall the Building Height for any
building exceed 18-feet. Chimneys may extend to 24-feet.
3.4 BUILDING FORMS AND MASSING
In general, buildings shall be asymmetrical, one story masses with larger masses located in the
middle of the mass. Building massing shall be a composition of horizontal rather than vertical
masses, punctuated and articulated by entries, varying levels, offsets, deep set windows and doors,
and building projections such as pergolas, trellises and/or covered porches.
Massing shall reflect room size volumes or groups of masses rather than one dominant
mass.
Massing designs shall be based on vernacular desert architecture which, in general, employs
groups of distinct and simple geometric forms emphasizing a low profile and wall, rather
than roof, compositions.
The play of light and shadow between Building Masses shall be carefully formulated to
articulate masses, accentuate entries and/or building levels and to create texture.
In general, larger masses shall be located in the middle of the Lot while smaller masses
shall be located along the perimeter of the Private Area.
Buildings shall be designed to be viewed from all sides. Screening and/or designing service
29
areas as integral parts of the overall architectural composition is required.
Building designs shall incorporate varied projections such as wall offsets, trellises, covered
porches or verandas that create texture, shade, scale and visual interest. Building ridgelines
or side walls shall not exceed 40-feet in one direction without a change in roof alignment, a
wall or elevation offset or broken by an appropriately scaled architectural element such as a
chimney.
Where ends of parapets are visible, they shall be a minimum of 16 inches in width.
Building masses shall have a strong indoor- outdoor relationship by incorporating
courtyards, breezeways and patios.
Entries shall be recessed and articulated with overhangs, porches and/or courtyards. Entry
elements shall be in scale with the home. Dominant or overly stylized entries shall be
avoided.
Detached garages which incorporate pergolas or trellises to connect to the main Residence
are encouraged to avoid large bulky forms.
3.5 ROOFS
Flat roofs are allowed provided they are not visually dominant when viewed from Community
Common Areas, the golf course or upper Lots. All roofs shall be carefully designed in color,
material and shape so that they help to integrate the structure with the site and neighboring
buildings and minimize the overall Building Massing. Trellises and outdoor covered areas shall be
incorporated into the overall massing to avoid a “tacked” on appearance.
Requirements for ‘Front Row’ Lot Roofs: From many viewpoints within the Community, roofs
will become a dominant visual element and must be designed to create a harmonious relationship
with the street, landscape and adjacent structures. Accordingly, those homes with roofs in view of
homes on higher elevations must be designed with these views in mind. To avoid any homes
looking down upon flat roofs, some Lots are required to have pitched roofs that conform to the
guidelines listed below. These Lots are allowed a maximum of 100 square feet of flat roof area,
provided this flat roof is not visible from any overlooking Lots. See Appendix B - Roof Form
Table for Lots affected by this requirement.
Roof Forms: Flat roof forms may include stylized parapet walls, fascias and/or overhangs. Low
pitched roof forms may include gable, hip and/or shed roofs (for minor building elements). All
pitched roofs shall be of a low pitch to reinforce the traditional forms and scale of the landscape.
Roof Pitches: Sloped roof pitches should be a maximum of 4:12. Roof designs shall incorporate
offsets and/or multi-level designs to avoid the appearance of wide, unbroken roof planes as viewed
from above or off site.
Acceptable Roof Materials: Materials for roofs are to be two-piece barrel tiles, flat tile, slate, or
built- up roofing for flat roofs. Roof tiles should utilize a minimum of four different, muted, earth
tone, complimentary colors, or diluted factory blends that create a subtle, multi-color surface. The
overall color impression of the tile roof should be dark, blending with the colors of the adjacent
Santa Rosa Mountains. Flat roofs must be painted a very dark color (LRV of 26 or lower) or be
surfaced with a material of a color that harmonizes with the natural desert and has an LRV of less
than 26. All roof materials must be non-combustible.
30
Unacceptable Roof Materials: Reflective roof finishes, any metal material that may cause
excessive glare, and asphalt or wood shingles are not acceptable. Simulated roof materials are not
acceptable.
Eave Depths: Eaves shall be incorporated where appropriate, 2-foot minimum. Exposed rafter tails
with wooden soffits are encouraged on sloped roof designs.
Gutters and Downspouts: Gutters, if used, shall be incorporated into the overall design of the
house. Gutters and downspouts shall not appear as if they were “tacked” on.
3.6 EXTERIOR WALLS
In general, the exterior wall design of all Residences and Improvements may incorporate the use of
at least two different complimentary materials in order to create subtle textural changes and to
further articulate masses. Exterior walls of a single material may be acceptable if, in the opinion of
the DRC, they meet the requirements of these Guidelines and are consistent with the
Neighborhood’s aesthetic goals.
Exterior wall design: The minimum exterior wall thickness shall be sufficient to allow windows
to be recessed a minimum of 6-inches on the street and golf course elevations and 1.5-inches on the
side yard elevations. Walls shall be simple, refined compositions of two materials in a logical
structural relationship. No building shall use more than three materials on the exterior walls.
Changes in material shall occur on the inside corners of masses.
Exterior Wall Height: In general, the exterior wall height from finish floor to top of wall plate
shall be 10-feet for the first floor. In no case shall an unbroken vertical plane be more than 12-feet
in height.
Acceptable Materials: Natural Stone, stabilized adobe block, and stucco with architectural accent
elements such as fascias, beams, window and door treatments and/or trim utilizing wood, stone, tile
and/or ornamental metal. Faux stone may be considered if coarsing, jointing, corners, lintels and
sills are detailed to appear structural in nature.
Stone/Rock: Stone may be used in the following manner:
as a foundation element with plaster/ stucco walls above;
as full height walls when used as the predominant wall material or as a foundation base;
and/or
as an accent in a cut pattern surrounding doors, windows or openings.
Stone masonry is to be one of two styles: either a dry-laid structural appearance similar to the rock
walls of the region, or uncoursed stone with minimal grout showing. Thin stone veneers applied in
geometric or random patterns that are not structural in appearance are not permitted.
Exterior Plaster and/or Stucco: Stucco may be utilized for foundation elements or full height
walls as discussed above in Stone/Rock. Walls shall have a “handcrafted” appearance utilizing
wavy textures or troweled patterns in a light to medium texture. Heavily textured stucco patterns
will not be permitted.
31
Adobe Block and Slump Block: The use of adobe or slump block as a principal building element
is encouraged because of their natural properties of insulation and the ability to create straight
and/or gently curved walls with a “handcrafted” appearance. Adobe may be exposed or properly
sealed with stucco to resist temperature changes or inclement weather.
Unacceptable Materials: Materials which are inappropriate are exterior plaster or stucco using a
heavy texture such as a swirl pattern, heavy sand, Spanish lace, or heavy troweled pattern, thin
stone veneers that are not structural in appearance, large expanses of unshaded glass, metal
cladding, and/or exposed concrete or concrete block.
3.7 DOORS AND WINDOWS
All windows and doors shall be deeply recessed and shaded to create pattern, texture and a sense of
thickness to the walls. Careful consideration shall be given to the fenestration design for each
elevation. The size, number, placement and rhythm of windows and doors in relation to the
Building Masses and exterior surfaces should create a complete and balanced composition.
Windows: Vertical, primarily casem*nt and/or double hung. Windows shall be deeply recessed a
minimum of 6-inches on street/front and golf/rear elevations, and 1.5-inches on side elevations.
Windows may utilize shallow arched, square or vertical shaped forms. Divided lite windows shall
utilize true divided lites.
Doors: Single or double door units, paneled, naturally stained wood, metal and/or multi-paned
glass are acceptable. Wood doors may be carved and/or have rough-sawn appearance. Door designs
should be consistent with each other, utilizing similar jamb, head and panel designs around the
entire exterior of the house. Where vents are required for exterior mechanical room doors, full
height louvers should be used.
Sliding or pocket doors with large glazed openings may be used provided they are protected by a
trellis or overhang providing deep shade over the glazed area. The depth of this trellis or overhang
shall be 1.5 times the door head height but in no case shall it be less than 12 feet in depth.
Window and Door Materials and Colors: Wood-clad or metal non-anodized finish. Unfinished
aluminum, vinyl or shiny metals are not permitted. Doors, window and door frames may be stained
and/or painted.
Accent Trim: Wood, decorative tile and/or stone accent materials shall be used in a consistent
manner around the structure.
Shutters: Operable shutters of wood, naturally stained or painted in appropriate designs that
borrow from regional vernaculars. Double shuttered windows shall be full sash height and half sash
width for the window they adjoin. Single shuttered openings shall be full sash height and width for
the window they adjoin.
Lintels: Cut or rough stone, decorative tile, cast stone and/or rustic, stained, rough sawn or refined
wood.
Glazing and Glass: All glazing shall meet energy codes. Glass may be coated or tinted to control
32
solar heat gain, but a reflective, mirrored appearance is not permitted. Large glazing areas should
be divided through the use of mullions or the ganging of smaller window units unless located under
deep overhangs/trellises as described above.
3.8 BUILDING PROJECTIONS AND ACCESSORY
STRUCTURES
The use of architectural extensions to provide shade and shadow, protect buildings from the intense
sun and create a strong indoor/outdoor relationship are outlined below. The style and details of
these architectural elements, such as column and eave treatments, should borrow from regional
vernacular or contemporary building traditions and be consistent with the architectural design of
the main Residence.
3.8.1 Pergolas/Trellises/Colonnades: Covered areas that connect separate Building
Masses, extend the roofline and/or are freestanding are strongly encouraged and are to be a
minimum of 6-feet wide.
3.8.2 Entry and/or Side Porches: Porches that provide shelter from the sun and accentuate
entry areas are to be a minimum of 6-feet in depth. Flooring materials are to be natural
stone, tile, colored concrete and/or colored concrete with stone and/or tile bands. In general,
the flooring shall be an extension or natural complement to the flooring used in the interior
of the building.
3.8.3 Railings: Decorative iron or wood carved railing details shall borrow from regional
vernacular or contemporary building traditions.
3.8.4 Mechanical Equipment, Vents and Flues: Roof mounted mechanical equipment,
vents and flues must not be visible from adjacent Lots or Common Areas. On sloping roofs,
these elements must be concealed within architectural structures (i.e., chimneys). Small
vents or flues may be painted to match the roof color. Ganging of vents/flues is required to
minimize the number of projections. Roof mounted mechanical equipment is prohibited on
sloping roofs. On flat roofs, all equipment, vents and flues must be concealed behind
parapet walls, chimneys or other architectural elements.
3.8.5 Miscellaneous Projections: All projections, including but not limited to, chimneys,
chimney caps, vents, gutters, down spouts, utility boxes, services, etc. must be incorporated
into the overall design. These items must be included on the submittals and reviewed by the
DRC for approval.
3.8.6 Accessory Structures: The design of accessory structures must be consistent with the
main Residence, integrated into the overall Residence composition and are to be visually
related to it by walls, courtyards, or major landscape elements. A freestanding guesthouse
must comply with applicable City zoning regulations and have the written approval of the
DRC.
3.8.7 Chimneys: Fireplaces and chimneys can be dominant elements of an architectural
33
composition. Accordingly, they must be proportionate to and consistently detailed with the
overall design. Fireplaces must be equipped with an approved spark arrester. Flue pipes are
required to be encased with a chimney enclosure of masonry or stucco and supported by a
foundation at grade when located on an exterior wall. Chimneys located on exterior walls
must be structural in appearance and relate to other expressed structural elements in the
design. Exposed metal flues are unacceptable.
3.8.8 Awnings: Canvas or similar type awnings over windows or doors are strongly
discouraged and will be allowed only if not visible from Common Areas, the golf course or
adjacent Lots and must be a subdued, earth tone color.
3.9 COLOR
The color palette for residences at Canyon View Estates will use muted and
recessive colors that will allow the natural colors of the desert to predominate,
complementing rather than contrasting with the setting. This palette is based on the
colors and hues of the surrounding desert geology and landscape. A pre-approved color
chart has been created for the community including approved Primary and Accent Colors.
An LRV of 44 or lower is required except as noted in the pre-approved color chart. If you
wish to submit an alternate color not listed on the pre-approved color chart your selection
will require adhering to the following basic color concepts:
Earth tones: Earth tone colors, with their organic origins, should be used for the primary
color composition.
Recessive Colors: Colors that recede, rather than advance, should be used. Generally, these
are darker colors. A wide variety of colors may be used, but all must have a Light
Reflective Value (LRV) of 44 or lower. All paint manufacturers categorize their products
by LRV and this information is readily available if not indicated directly on color swatches.
Light or bright colors generally have an LRV greater than 44.
Multi-hued: Large areas of monochromatic surfaces tend to stand out in the bright desert
sunshine. As a result, colors that have a “tonal complexity” should be employed. With
certain materials, such as stucco, this multi-hued quality may be achieved through surface
texture and quality.
In dealing with color the DRC will consider the entire Neighborhood as well as the individual
Residence for submission.
The Committee will review and approve colors and textures in a three step process. During the
Schematic Design phase, the applicant may describe the color palette and indicate those colors on
the exterior elevations. In the Preliminary Design and Final Design Submissions the applicant will
submit actual color and material samples. Based on these, the applicant will, during the
construction phase, then be required to provide a 48 square foot panel on site of the intended
colors, materials and textures of the major building elements for final approval.
The palette and following guidelines apply to all exterior surfaces of the house, including walls,
parapets, roofs and all related fences and walls:
No exterior materials used shall have a high gloss, glare, or reflective “mirror” type finish.
34
Color application should be used consistently throughout each Home for all the building(s)
and related outdoor areas and/or structures.
Colors for large field application shall be a combination or layering of two or three colors to
achieve a “multi-hued” quality which changes with light and shadow, rather than a “flat”
appearance. Large, monochromatic surfaces, with the exception of flat roofs, are not
acceptable.
Colors for roofing shall be darker in color or hue than the building’s exterior walls.
Colors for large field application should be recessive in value, while accent color, used in
limited areas, may “advance” towards the viewer.
Accent colors should be carefully considered for front doors, window sashes and other
architectural elements so that they do not dominate or overwhelm the overall color
composition.
Exterior hardscape colors should be complementary to exterior home colors.
Changes in exterior wall color should be made at “interior” intersections of walls.
No white, or excessively light colors will be allowed
Roofs: Medium to dark browns and grays, color shall have a LRV of 35 or lower. Flat roofs shall
have an LRV of 26 or lower.
Walls: Natural and earth tones. Large areas of monochromatic surfaces shall be minimized. Wall
surfaces shall utilize texture and/or multi-layered applications of color where possible to achieve
subtle color variation on walls. Walls shall have an LRV value range of 44 or lower. Wall colors
with a higher (brighter) LRV of 44 will be considered when a substantial portion of the exterior
wall surfaces utilize a darker stone.
Trim and Accent Colors: Dark, rich earth tones that come from stains, woods and/or paint.
Accent areas shall have an LRV value of 55 or lower.
35
Pre-Approved Paint Colors:
Company Name Color Name – PRIMARY Or Accent
Color Number
LRV
Valspar
Caramelized Onion 2008-9B 22
Cincinnatian Hotel Carl Tan 3002-9C 36
Faint Maple 2008-9C 38
Free Wheeling 2006-10A 44
Mocha Syrup 3002-9B 20
Crushed Red Pepper C192 10
Seashell Gray 4003-1A 28
Mona’s Mane 3001-9A 15
Sumatra Blend 2008-9A 13
Sherwin-Williams Highland Grey HGSW2444 32
Lite Ledgestone HGSW2473 22
Sea Otter HGSW2441 11
Terminal Taupe HGSW2474 30
Tynewood HGSW2442 14
Weather Worn HGSW2472 15
Olympic Coffee Kiss OL689.5 C11 31
Flipper OL144 21
Gibraltar Grey OL143 13
Hat Box Brown D21-5 19
Kodiak D21-6 9
Oyster Shell D14-4 28
Patches OL146 N27 21Q
Sautéed Mushroom D21-4 30
Seal Skin D14-6 10
Simmering Smoke OL171 36
Stony Fields D14-5 16
Talavera OL130 29
Timber Beam OL692-4 C14 24
Warrior OL145 15
36
3.10 DECORATIVE ELEMENTS
Wood Accent Elements: Due to climatic extremes, the use of wood on a residential exterior
should be carefully considered and limited to accent areas or specific building elements such as
entries, windows, beams, doors, covered porches and/or courtyards. Carved wood designs may
draw their inspiration from indigenous crafts such as pottery, basket and/or textile designs and/or
building techniques of the region such as traditionally carved canales, vigas, corbels and/or beams.
Ornamental Metal Accent Elements: Metal may be used for railings, decorative window grilles,
and/or gates provided that the design draws upon the indigenous patterns and styles of the region, is
not reflective and has the appearance of iron, weathered bronze, brass or copper.
3.11 UTILITIES
Cooling and Heating Equipment - All equipment shall be located within the Building Envelope
and fully screened from Common Areas, the golf course, and adjoining Lots. Ground-mounted
units are encouraged. The design shall locate units so as to minimize noise associated with the
operation or maintenance of the units. Screen walls shall completely enclose the units, with the
wall a minimum of one-foot higher than the highest part of the unit. In some cases, property line
privacy walls may be sufficient to achieve screening of equipment areas, eliminating the need for a
‘double’ wall. Roof- mounted units on sloped roofs are not allowed. Acoustic wall and/or covers
may be required if it is discovered that noise emanating from enclosures are a nuisance to adjoining
Lots, the golf course or Common Areas.
Solid Waste Disposal - Trash and refuse areas shall be designed as integral parts of the building
design. These areas must be screened from Common Areas, the golf course, and adjoining Lots.
Covers on trash enclosures may be required if it is discovered that odors emanating from
enclosures are a nuisance to adjoining Lots, Common Areas or the golf course. All trash containers
must have sealed lids.
37
CHAPTER FOUR
LIFE AND SAFETY CONSIDERATIONS
The following chapter outlines Guidelines for systems regarding life safety, such as fire sprinklers
and alarm systems, and presents ways in which to build resource and energy-efficient buildings.
4.1 ENERGY AND RESOURCE CONSERVATION
MEASURES
Site and building design with construction techniques which utilize the latest advances in energy
and resource conservation and home technology are encouraged. New building technologies,
innovative building materials, thoughtful site planning and creative construction systems can be
used to create more energy-efficient, durable, and better quality • homes.
The following measures are strongly recommended in the planning and design of a home at
Canyon View Estates.
Suggested Energy Efficiency Measures
Living areas, such as living rooms, dining rooms, kitchens and bedrooms, should be
planned for maximum ventilation. Locate windows for natural light and cross- ventilation.
Shading devices should be used for unwanted heat gain.
Consider increasing the required insulation in walls, ceilings and foundations to reduce
energy consumption and to lower utility bills.
Seal and insulate duct work and locate in “conditioned” spaces where possible.
Install high-performance windows.
Suggested Resource Efficiency Measures
Building construction and design should emphasize efficient building practices and the
reuse and reduction of materials. Sort construction and demolition waste for recycling by
utilizing job site bins for wood, metals, wallboard etc.
Building designs should include adequate space for recycling bins in kitchens, utility areas,
and trash enclosures.
All buildings should utilize high-efficiency (low flow) showerheads, toilets, faucets and
similar appliances.
4.2 SKYLIGHTS
Skylights must be integrally designed into the roof structure. Skylight glazing shall not be back-lit
or manufactured of reflective material. Skylight framing and glazing shall be colored or coated to
match adjacent materials. Light emanating from the interior though a skylight is subject to the same
controls as light emanating from a window as described in Section 2.16 Lighting. Bubble-type
glazing is not permitted.
38
4.3 SOLAR EQUIPMENT
Solar Equipment is acceptable subject to the installation being consistent with the aesthetic
expectations for the community which are described in the design guidelines. It is suggested that
solar panels arrays be located on flat roof sections and screened by parapet walls. Where these
conditions are not available, as a courtesy to your neighbors, the installation of solar panels is not
recommended unless the panels can otherwise be screened from public and neighborly views.
Panels should be a dark color so as not to be reflective and should be recessed within the
composition of the roof as best possible. All support structures should be hidden from view and/or
painted a color that will blend with the roof material where necessary. All proposed solar panel
installations are required to be submitted to the Association and should be in compliance with the
intent of the Guidelines with regard to aesthetic expectations and installation quality.
SUBMITTAL REQUIREMENTS
Existing & New Home Sites: (2 Sets)
1. Site Plan/Roof Plan
Minimum: 1/8” scale
Aerial photos of existing site at proportionate scale (equivalent to the site plan) for
review.
Looking down from a near vertical position.
Looking from adjacent home sites out over roof elements where solar panels and
support devices are proposed.
Looking from critical HOA and golf course view corridor locations out over roof
elements where solar panels and support devices are proposed.
2. Show proposed solar panels and support devices.
3. Show all existing roof elements and describe material and slope of existing roof elements.
4. Show location of all solar equipment(s) and panels including conduits and panels for power
and control, support brackets and hardware.
5. Show location of all ground equipment and/or panels.
6. Show adjacent home sites status: finished pad heights of proposed project as well as
adjacent home site pads (Photos are sufficient).
7. Provide roof cross sections (minimum: 1/8” scale) of each respective roof element to
receive solar equipment/panels in order to show how panels will be installed on the existing
roof element. (If not on roof, show proposed location).
8. Provide cross-referenced architectural detailing as required (minimum: 1” scale) to show
specifics on how panels, hardware and support frames will be attached and integrated into
the existing roof elements.
39
9. Provide all applicable architectural exterior elevation drawings and/or photographs with
editing as required to show full installation from all views.
Minimum: 1/8” scale.
Show all existing building elements as well as major plant massing elements.
Show all proposed solar panels, visible equipment(s), bracketing and support
structures as well as utility and control panels as seen in each respective
elevation view.
Provide cross-referencing to applicable architectural detailing as mentioned
above, under cross sections of roof.
10. Copies of proposed system components, manufacturer, required installation details and
instructions.
11. Provide color specifications for all solar system components including utility panels,
conduits, wiring, support brackets, etc.
12. Describe the access requirements/locations for maintenance and servicing of system after
installation.
In addition to the fee schedule set forth for new construction or remodels, a $500 surcharge
may apply to cover the cost of a solar engineering review by a third party consultant.
Comment: The committee suggests that prior to installation, research be conducted to ensure
that installation of solar panels and equipment will not affect your roof integrity or home
warranty.
40
CHAPTER FIVE
DESIGN REVIEW PROCESS
This section provides a guide for the Design Review Process for the Canyon View Estates. The
process involves a series of meetings between the Owner, their design team and the DRC. The
process begins with an informal introductory meeting and concludes with the completion of
construction. Along the way are a series of meetings designed to ensure a smooth and efficient
review of the building and site design. The DRC is committed to assisting Owners through the
Design Review Process and should be thought of as a member of the Owner’s design team as
opposed to a regulatory review agency.
5.1 OVERVIEW OF DESIGN REVIEW PROCESS
Improvement plans will be carefully reviewed by the DRC to ensure that the proposed design is
compatible with the design intent at Canyon View Estates. This Design Review Process must be
followed for any of the following Improvements:
Construction of all new buildings;
The renovation, expansion or refinishing of the exterior of an existing building;
Major site and/or landscape Improvements (including pools, driveways and/or culverts);
and
Construction of, or additions to, fences or enclosure structures. The DRC evaluates all development
proposals on the basis of these Design Guidelines. Some of the Guidelines are written as broad
standards and the interpretation of these standards is left up to the discretion of the DRC. Other
Guidelines, such as Building Height or setbacks, are more definitive, or absolute, design
parameters and in many cases parallel City and building code requirements or project approval
documents. It is the intention of this Design Review Process that all Improvements comply with
these absolute standards. In the event of a conflict between these Guidelines and any local, state or
federal building or zoning code or project approval documents, the local, state, or federal building
or zoning code or project approval documents shall govern.
The Canyon View Estate’s Design Review Process takes place in four steps:
1. Pre-Design Conference & Schematic Design
2. Preliminary Design Review
3. Final Design Review
4. Construction Observation
Any Improvement as described above will require and be preceded by the submission of plans and
specifications describing the proposed Improvements accompanied by an application fee.
The Owner shall retain competent assistance from an Architect, Civil Engineer, Landscape
Architect, Soils Engineer and a licensed and bonded Contractor (Consultants) as appropriate. The
Owner and Consultant(s) shall carefully review the CC&R’s and these Design Guidelines prior to
commencing with the Design Review Process.
41
Having secured Preliminary Design approval from the DRC, the Owner is also required to meet all
the submittal and approval requirements of the City of Palm Desert Planning and Building
Department to obtain design approvals or any other discretionary permits and a building permit.
The Owner is to commence construction within one year of the Final Design approval. If
construction does not commence within this timeframe the design approved will expire, requiring
resubmission of the application and payment of all associated fees.
5.2 APPROVED DESIGN PROFESSIONALS
Contact the Association Office for more information.
5.3 PRE-DESIGN CONFERENCE & SCHEMATIC DESIGN
5.3.1 PRE-DESIGN CONFERENCE
Prior to the preparation of any materials for formal DRC review, the Owner and/or the
Consultant(s) are required to meet with representatives of the DRC for a Pre-Design Conference.
An explanatory Pre- Design Conference package that includes a current copy of the Design
Guidelines, the Lot Diagram and a conference request form is available from the DRC Office. The
purpose of this meeting will be for the DRC to answer any questions the Owners and/or
Consultant(s) may have and to offer guidance on the following subjects:
The particular characteristics and restrictions on the Lot, as shown on the Lot Diagram, to
be provided by the DRC;
Optimal orientation of buildings and outdoor spaces;
Additional survey information requirements;
Preliminary building and site development program ideas and requirements;
Clarification and review of Design Guideline objectives;
The requirements, fees, and schedule of the Design Review Process.
5.3.2 SCHEMATIC DESIGN
After or during the Pre-Design Conference, the Applicant shall submit to the DRC a written
application and appropriate fee for Schematic Design Review together with the Schematic Design
Review submission materials as described below:
1. Schematic Design Review Application Form (Sample in Appendix).
2. Design Review Application Fee (see Section 5.15).
3. Schematic Site Plan: (1”=20’, 16’ or 8’) indicating property lines and Lot Diagram areas,
building location/footprint; driveways, pools, water features and other major hardscape
elements and basic grading concepts.
4. Schematic Floor Plan: (1”=20’, 16’, or 8’) showing general room layout and circulation.
This may be combined with the Schematic Site Plan.
5. Schematic Elevations: (1”=16’ or 8’) of the street and golf sides of the building showing
general massing, roof forms, building height and materials.
42
The purpose of this submittal is to confirm that the design professionals are headed in the right
direction, are correctly interpreting the Guidelines and that the Owner’s program can be
accommodated on the Lot. This submittal may be combined with the Pre-Design Conference.
Upon receipt of a Schematic Application the Design Review Committee will notify
neighboring property Owners within a 500-foot radius of the submittal. Neighbors may
request an appointment to review the plans with the Association Manage r or DRC
Facilitator. An appointment will be set up within seven (7) Working Days of receipt of
the written request.
5.4 PRELIMINARY DESIGN REVIEW
After the Pre-Design Conference and Schematic Design, the Owner shall submit a written
application for Preliminary Design Review together with Preliminary Design Review submission
materials, described in Section 5.4.1 below.
5.4.1 PRELIMINARY DESIGN REVIEW SUBMISSION MATERIALS
Within this step, the Applicant shall prepare and submit to the DRC for review and approval a
Preliminary Design Review package which should adequately convey existing site conditions,
constraints, building orientation and design, vehicular and pedestrian access, the proposed use of
exterior materials and colors and conceptual landscape design. The package shall include one (1)
full-size set and one (1) set of 11” x 17” reductions along with a disc containing PDF’s of the
following drawings and/or materials:
1. Preliminary Design Review Application Form (Sample in Appendix) 2. Parcel Survey - a property survey (minimum scale: 1” = 20’) prepared by a licensed
surveyor indicating property boundaries, the area of the property, all easem*nts of record,
utilities, 100-year flood plain, one- foot contours, any significant natural features such as
existing trees, or any significant drainages as applicable. See Appendix F - Lot Survey
Requirements.
3. Preliminary Site Plan - 1”=20’ minimum, showing existing topography and proposed
grading and drainage (1-foot contour interval), existing off-site elements (buildings, walls,
tree, etc.) within 20 feet of the property boundary, building footprint with finished floor
grades, setbacks, Building Envelope and other zones as indicated on the Lot Diagram,
driveway, parking area, turnarounds, drainage, fences/walls, roofs, patios, decks, pools,
and any other site amenities.
4. Preliminary Floor and Roof Plans - minimum 1/8” = 1’-0”, including all proposed uses,
proposed walls, door and window locations and location of mechanical and electrical
systems.
5. Preliminary Elevations - minimum 1/8” = 1’-0”, including roof heights, existing and
finish grades, building heights and notation of exterior materials. Two sets of elevations,
one set should be rendered in color.
6. Site Sections - minimum scale 1” = 20’, showing proposed buildings, building heights,
elevations and existing and finished grades in relation to surrounding site, including
adjacent Residences and Roads as may be required by the DRC.
43
7. Conceptual Landscape Plan - a conceptual plan at 1” = 20’ minimum, showing irrigated
areas, areas of planting, turf areas, preliminary plant list, Building Envelope and other zones
as indicated on the Lot Diagram, water features, pools, patios, decks, and any other
significant design elements. This may be combined with the Site Plan.
8. Grading, Drainage and Erosion Control Plans - 1” = 20’ minimum, showing existing
and proposed grading (1-foot contour interval), drainage elements and erosion control
methods. Site plan should include twenty feet beyond Homeowner’s property line in order
to depict relationship to adjacent Lots and Common Areas.
9. Study Model or Color Rendering – minimum scale 1” = 20’, illustrating the relationship
between proposed building forms and topography, tree heights and prevailing site
conditions. This need not be an expensively detailed model, but simply adequate to
communicate basic three-dimensional massing concepts. Computer drafted 3D modeling is
acceptable.
10. Material Samples – on 8-1/2 x 11 or 11 x 17 inch boards showing:
Roof material and color;
Wall material and color;
Exterior trim material and color;
Stone/rock materials;
Window/door materials and color;
Fence/wall materials and color;
Paving materials and color.
5.4.2 STAKING
The Owner may be required to stake the corner locations of the proposed buildings and all other
major Improvements upon submittal of Preliminary Design Review documents. In some instances,
the DRC may require that ridgeline flagging be erected to indicate proposed Building Heights.
5.4.3 PRELIMINARY DESIGN REVIEW MEETING
Upon receipt of the required documents and staking of the property (if required), the DRC will
notify the Owner of the scheduled meeting date to review the Preliminary Design documents. The
DRC will review and comment on the application at the meeting, allow time for discussion with the
Owner and/or Consultant(s) (if present) and subsequently provide the Owner with the conclusions
of the meeting in writing.
The comments of the DRC on the Preliminary Design submittal shall be advisory only, and shall
not be binding upon either the Owner or the DRC. A second review meeting may be necessary to
review corrected and/or new materials. Corrected materials will be provided to the DRC a
minimum of five working days prior to the next regularly scheduled meeting.
44
5.5 FINAL DESIGN REVIEW
Within one year of Preliminary Design Review approval the Owner shall initiate Final Design
Review by submitting required Final Design documents. Required Final Design documents and
procedures are described in Section 6.5.1 below.
5.5.1 FINAL DESIGN REVIEW SUBMISSION MATERIALS
The Applicant shall provide all information necessary to reflect the design of the proposed
building(s), landscape or other features requiring the approval of the DRC. Final Design documents
shall generally conform with the approved Preliminary Design Review documents. All
architectural plans are to be prepared by a licensed Architect. All landscape architectural plans are
to be prepared by a licensed Landscape Architect. The Final Design Review Documents shall be
Construction Document level drawings. Submit one (1) full size, one (1) set of 11”x17” reductions
and a disc with PDF’s of final plans that include the following:
1. Final Design Review Application Form 2. Site Plan - 1” = 20’ minimum, showing existing topography and proposed grading (1-foot
contour interval), building footprint with finished floor grades, Building Envelope and other
zones as indicated on the Lot Diagram, driveway, parking area, turnarounds, fences/walls,
patios, decks, utility connections and pad locations, pools and any other site amenities. Site
plan should include twenty feet beyond Homeowner’s property line in order to depict
relationship to adjacent Lots, the golf course and Common Areas.
3. Grading, Drainage and Erosion Control Plans - 1” = 20’ minimum, showing existing
and proposed grading (1-foot contour interval), drainage elements and erosion control
methods. Site plan should include twenty feet beyond Homeowner’s property line in order
to depict relationship to adjacent Lots and Common Areas.
4. Floor and Roof Plans - 1/4”=1’-0”, indicate all room dimensions, door and window
locations and sizes, location of mechanical and electrical systems and fire sprinkler and
monitoring systems. Indicate the location and type of all exterior lighting fixtures, proposed
fireplaces, and kitchen appliances. Provide floor plans of all Accessory Structures.
5. Elevations - 1/4”=1’-0”, illustrate the exterior appearance of all views labeled in
accordance with the site plan. Indicate the highest ridge of the roof, the elevation of each
floor, and existing and finished grades for each elevation. Describe all exterior materials,
colors, and finishes (walls, roofs, trim, vents, windows, doors, etc.) and locate all exterior
lighting fixtures. Indicate proposed Building Height. Provide one set of colored elevations.
6. Sections - indicate building walls, floors, interior relationships, finished exterior grades and
any other information to clearly describe the interior/exterior relationships of the building
as well as the building’s relationship to the site.
7. Landscape Plans - 1/8”=1’-0” minimum, including a planting plan, layout plan, irrigation
plan, lighting plan, and any site details including retaining walls, landscape structures,
pools, patios, fences and or gates. Call out all hardscape materials.
8. Sample Board - on 11” x 17” boards as needed:
Roof material and color
Wall materials and colors
Exterior trim material and color
Window material and color
45
Exterior door material and color
Stone/rock materials
Fence/wall materials
Exterior rails and paving materials
The DRC will review and comment on the sample board at the Final Design Review. Final
approval is contingent upon field mock-ups of all colors and materials at the appropriate time in the
construction process and in sizes / context that will allow a clear understanding of the final product.
Regardless of previous approvals, the DRC reserves the right to require changes to the field mock-
ups if they do not meet the objectives of the Design Guidelines. See section 7.19 for a description
of required material mock-ups.
9. Construction Schedule - include start and completion dates for both building and
landscape construction. All construction shall be started within one year of Final Design
approval and shall be completed within 18 months from start of construction.
5.5.2 FINAL DESIGN REVIEW MEETING
Upon receipt of the required documents, the DRC will notify the Owner of the scheduled meeting
date to review the Final Design documents. In some instances, the DRC may request a final staking
of the location of all corners of proposed buildings if the Final Design documents vary substantially
from approved Preliminary Design documents.
Attendance at the meeting by the Owner and/or Consultant(s) is not mandatory. The DRC will
review and comment on the application at the meeting, allow time for discussion with the Owner
and/or Consultant(s) (if present), and subsequently provide the Owner with an approval (see
Section 5.5.3 below) or conclusive recommendations in writing for refinements to the design. A
second review meeting may be necessary to review refinements, revisions and/or new materials.
These materials will be provided to the DRC a minimum of five working days prior to the next
regularly scheduled meeting.
5.5.3 FINAL DESIGN APPROVAL
The DRC will issue Final Design approval in writing within seven working days of a vote for
approval at a Final Design Review meeting. If the decision of the DRC is to disapprove the
proposal, the DRC shall provide the Owner with a written statement of the basis for such
disapproval to assist the Owner in redesigning the project so as to obtain the approval of the DRC.
5.6 RESUBMITTAL OF PLANS
In the event that final submittals are not approved by the DRC, the Owner will follow the same
procedures for a resubmission as for original submittals. An additional Design Review fee must
accompany each resubmission as required by the DRC.
46
5.7 CITY OF PALM DESERT APPROVALS AND OTHER
AGENCIES
The Owner shall apply for all applicable building permits from the City of Palm Desert Planning
and Building Department and any other governing agencies after receiving Final Design approval
from the DRC. Any adjustments to DRC-approved plans required by City review must be
resubmitted to the DRC for review and approval prior to commencing construction. The issuance
of any approvals by the DRC implies no corresponding compliance with the legally required
demands of other agencies.
5.8 SUBSEQUENT CHANGES/MAINTENANCE/REMODELS
Subsequent construction, landscaping or other changes in the intended Improvements that differ
from approved Final Design documents must be submitted in writing to the DRC for review and
approval prior to making changes.
MAINTENANCE AND REPAIR
Maintenance and repairs are encouraged. It is to the benefit of all Canyon View residents that
homes and landscapes be maintained in a premier condition. Maintenance and repair should be
undertaken with the goal to keep the exterior of the residence in compliance with the plans
originally approved by the Design Review Committee (DRC). The following guidelines are
designed to be accommodating with minimal procedure and no cost to the homeowner.
Level One Maintenance and Repair:
Minor maintenance and repair to the structure, landscape or hardscape that occur on a routine basis.
Review, fees and notification do not apply.
Examples of Level One Maintenance and Repair items include but are not limited to:
Touch-up of plaster, paint or stucco in select areas on the exterior of the home or any
property walls with exactly matching materials.
Minor repairs to architectural stone work.
Minor touch-up to windows and doors such as annual maintenance of wood frames using
the matching stain.
Minor repairs to the roof for missing or broken tiles or fixing minor leaks using matching
tiles.
Thinning of landscape plant material
Annual tree or palm pruning
Replacement of dead or overgrown plant material with the same plant material.
Minor hardscape repair.
Landscape lighting repair to existing fixtures or replacement of a damaged fixture with the
same fixture.
47
Level Two Maintenance & Repair:
More extensive maintenance and repair to the structure, landscape, or hardscape that maintains a
consistent and/or complimentary design concept, intent, layout, materials, detailing, colors and
textures as originally approved by the DRC. Review and fees do not apply. For security and
traffic purposes, notification to Canyon View Estates/Ironwood Security is recommended.
Examples of Level Two maintenance and repair items include but are not limited to:
Repainting the structure, or a significant portion of the structure, with no change in paint or
stucco color.
Repainting the perimeter walls, retaining walls and garden walls with no change in paint or
stucco color.
Replacement of a damaged palm or other tree with the same species. (Refer to Guidelines)
Hardscape replacement with the same materials and color.
Level Three Maintenance & Repair:
Major maintenance and repairs to the structure, landscape or hardscape that are not routine but
maintain the design, layout, materials, details, colors and textures as originally approved by the
DRC. Notification to the DRC Facilitator or Association Manager is required. Depending on the
complexity of the proposed repairs, the ADRC may require information regarding the current
conditions and the proposed repair. Approval by the DRC, including site visits, may be required.
Examples of Level Three maintenance and repair items include but are not limited to:
Replacement of a palm or other tree with a different species (refer to guidelines).
Removing a palm or other tree without replacement.
Repair of landscape lighting with materially different fixtures, type of bulbs, intensity, etc.
48
REMODEL
Remodel procedures evolve as the community ages and more significant modifications to existing
homes are submitted. The Design Review Committee (DRC) requires a Remodel Application form
be submitted for approval prior to the start of either design work or changes in the field (including
minor changes). With a short preliminary description of the intended changes/modifications to
your architecture, landscaping, or site, the committee will evaluate how detailed the actual
submittal needs to be. Based on this information the DRC will notify the Owner regarding the
applicable remodel level, along with the applicable review fees required. The Remodel will be
evaluated using the following criteria:
Level One:
Alteration to a limited portion of the original DRC approved plan that impacts the color, texture or
material of any structure, landscape or hardscape. The Remodel Application form along with
drawings and/or photographs and a detailed written description of the proposed modification is
required.
Examples of Level One modification include but are not limited to:
Changes in the exterior colors and/or materials.
Hardscape replacement with difference materials and /or color without change to the design
and size.
Changes to exterior lighting attached to the home.
Level Two:
Significant alterations to the home that still maintain the consistent and complimentary design
concept, intent, layout materials, detailing, colors and textures of the home and site. The Remodel
Application form along with appropriate drawings, photographs, and a written description detailing
the existing and proposed alterations is required.
Examples of Level Two modifications include but are not limited to:
Expansion of a room
Significant landscape or hardscape changes.
Pool, spa or water feature changes including design and layout, color /material changes, etc.
Level Three: Extensive modifications, room additions or other changes to the exterior of the residence or site
that alter the existing design style with regard to architecture, layout, size, detailing, materials,
colors, etc. The Remodel Application form along with comprehensive plans detailing the existing
and proposed conditions is required.
Examples of Level Three remodel include but are not limited to:
Changes to the exterior style of the home.
Structure additions.
Significant changes to the size and/or design of windows or doors.
Changes to the roof design and/or materials.
When a remodel is requested, the contractor, sub-contractor or contact person responsible for
overseeing the job must be identified.
49
The fee schedule for remodels is as follows:
Level One: DRC maximum Review Fee of Two Hundred and Fifty Dollars ($250) with no
Construction Compliance Deposit due.
Level Two: DRC maximum review Fee of Seven Hundred and Fifty Dollars ($750) and a
Two-Thousand Five Hundred Dollar ($2,500) Construction Compliance Deposit.
Level Three: DRC Review Fee of One Thousand Dollars ($1,000) and a Five-Thousand
Dollar ($5,000) Construction Compliance Deposit.
5.9 WORK IN PROGRESS OBSERVATIONS
During construction, the DRC will check construction to ensure compliance with approved Final
Design documents. If changes or alterations have been found that have not been approved, the
DRC will issue a Notice to Comply.
5.10 NOTICE TO COMPLY
When, as a result of a construction observation, the DRC finds changes and/or alterations that have
not been approved, the DRC will issue a Notice to Comply within three working days of the
observation. The DRC will describe the specific instances of non-compliance and will require the
Owner to comply or resolve the discrepancies.
5.11 NOTICE OF COMPLETION
The Owner will provide the DRC with a Notice of Completion of any Improvement(s) given Final
Design approval by the DRC. The DRC will make a final inspection of the property within seven
working days of notification. The DRC will issue in writing a Notice of Completion within seven
working days of observation. If it is found that the work was not done in compliance with the
approved Final Design documents, the DRC will issue a Notice to Comply within three working
days of observation.
5.12 RIGHT OF WAIVER
The DRC recognizes that each Parcel has its own characteristics and that each Owner has their own
individual needs and desires. For this reason, the DRC has the authority to approve deviations from
any of the Design Guidelines or Regulations contained within this document. It should be
understood, however, that any request to deviate from these Design Guidelines will be evaluated at
the sole discretion of the DRC, and that the approval of deviations will be limited to only the most
creative design solutions to unique situations. Prior to the DRC approving any deviation from a
Design Guideline, it must be demonstrated that the proposal is consistent with the overall
objectives of these Design Guidelines and that the deviation will not adversely affect adjoining
Parcels or the Neighborhood of Canyon View Estates as a whole. Approval of any deviation from
the Design Guidelines shall not set a precedent for other applicants to seek a similar deviation.
The DRC also reserves the right to waive any of the procedural steps outlined in this Design
Guideline document provided that the Owner demonstrates there is good cause.
50
5.13 NON-LIABILITY
Neither the DRC nor any member, employee or agent will be liable to any party for any action, or
failure to act with respect to any matter if such action or failure to act was in good faith and without
malice.
5.14 DESIGN REVIEW SCHEDULE
The DRC will make every reasonable effort to comply with the time schedule for Design Review.
However the DRC will not be liable for delays that are caused by circ*mstances beyond their
control. The DRC will provide Design Review according to the following schedule:
1. Pre-Design Conference & Schematic Design Review
a. Meeting scheduled within 14 working days of receipt of Pre-Design Conference
request form.
2. Preliminary Design Review a. Application documents to be submitted 14 working days prior to the next scheduled
DRC meeting, and within one year of Preliminary Design approval.
b. Written comments from DRC meeting and/or written notice of Final Design
approval provided to Owner within seven working days.
c. A second review meeting may be necessary to review refinements, revisions and/or
new materials. These materials will be provided to the DRC a minimum of five
working days prior to the next regularly scheduled meeting.
d. Foundation observation within 7 working days of receipt of written request.
3. Final Design Review
a. Application documents to be submitted 14 working days prior to the next scheduled
DRC meeting, and within one year of Preliminary Design approval.
b. Written comments from DRC meeting and/or written notice of Final Design
approval provided to Owner within seven working days.
c. A second review meeting may be necessary to review corrected and/or new
materials. Corrected materials will be provided to the DRC a minimum of five
working days prior to the next regularly scheduled meeting.
4. Building Permits
a. Owner applies to the City of Palm Desert for all applicable building and use permits.
5. Construction Observation
a. Site observation with the Builder prior to any site disturbance, and within seven
working days of receipt of written request.
b. Framing observation within seven working days of receipt of written request.
c. Final observation within seven working days of receipt of written request and prior
to request for a Certificate of Occupancy from the City of Palm Desert.
d. Notice of Completion issued within seven working days of observation.
51
5.15 APPLICATION FEES
In order to defray the expense of reviewing plans, monitoring construction and related data, and to
compensate consulting Architects, Landscape Architects and other professionals, these Guidelines
establish a total fee of $3,500 payable upon submittal of the application for the Pre-Design
Conference or Preliminary Design Review.
Fees for resubmission and remodels will be charged per the Remodel Fee Structure.
The Builders Bond will be $10,000 due prior to the start of construction.
5.16 APPLICATION FORMAT
An application and information package is available from the DRC for each submission. Each
submission must be accompanied by the required information, as specified in the application
package instructions and these Guidelines, in order to be scheduled for review. Incomplete
submissions will not be reviewed and may be returned to the applicant for resubmission.
52
CHAPTER SIX
CONSTRUCTION AND BUILDER REGULATIONS
6.1 PRE-CONSTRUCTION CONFERENCE
Prior to commencing construction, the Builder must meet with an authorized representative of the
DRC to review the approved Final Plans, the Construction Area Plan, the Construction
Regulations, and to coordinate scheduling and construction activities with the DRC. At this
meeting, the Builder or Owner must bring a copy of the Building Permit issued and any related use
permit from the City of Palm Desert Building Department.
6.2 CONSTRUCTION AREA
Prior to the commencement of any Construction Activity the Builder will provide the DRC, for its
approval, with a detailed plan of the proposed Construction Area showing the area in which all
Construction Activities will be confined and how the remaining portions of the Lot will be
protected.
This Construction Area Plan will designate the location and size of the construction material
storage and parking areas, and the locations of the chemical toilet, temporary trailer/structure,
dumpster, debris storage, fire fighting equipment, utility trenching, limits of Excavation and
erosion control.
Fencing Requirements
The Plan should identify the area to be fenced with chain link with shade screen fencing or similar
methods for the protection of existing landscaped areas, to screen construction activities and to
control dust. Such fence or screening material shall be maintained in good condition during the
course of construction of the Residence and related Improvements. One entrance into the fenced
enclosure shall be located at the driveway entry.
Care must be taken to avoid, or if unavoidable, minimize the visual impact of the Construction
Area on neighboring Lots, Public Areas and Roads.
Prior to construction, all golf course planting, side yard planting and streetscape elements will be
photographed by DRC to record existing site features.
53
6.3 BUILDER’S BOND
After the DRC approves an Owner’s proposed Construction Area Plan as described in Section 6.2,
and prior to commencing any Construction Activity, a Builder’s Bond shall be delivered to the
DRC, on behalf of the Association, as security for the project’s full and faithful performance of its
Construction Activity in accordance with its approved final plans. This Builder’s Bond shall be a
cash bond.
The amount of the Builder’s Bond shall be $10,000 per Lot for the new residences. Remodel fees
are noted under Section 5.8 of the Guidelines.
The DRC may use, apply or retain any part of a Builder’s Bond to the extent required to reimburse
the DRC for any cost that the DRC may incur on behalf of the project’s Construction Activity. Any
monies shall be reimbursed to the DRC for any fees incurred by the DRC to restore the Builder’s
Bond to its original amount. Construction Activity shall be halted until the Builder’s Bond is
brought up to the original amount.
The DRC shall return the Builder’s Bond to the Owner within 15 working days after the issuance
of a Notice of Completion from the DRC.
6.4 ACCESS TO CONSTRUCTION AREA
1 Canyon View Estates requires all Builders to comply with the following:
2 Restrict access to the Construction Area only through the Canyon View Estates
construction gate.
3 Identify all vehicles entering Canyon View Estates with the Builder’s name and job site.
4 Enforce hours of access, speed limit and route of travel on the Canyon View Estates road
system as specified by the DRC.
5 Limit access to the Construction Area only on designated routes as specified by the DRC.
6 Consolidate all deliveries of materials and equipment to the extent feasible.
7 Acquire transponders per the club’s requirements at their own expense.
6.5 VEHICLES AND PARKING AREAS
Only vehicles, equipment and machinery that are essential to any Construction Activity may park
within the Construction Area or such other specific area designated by the DRC so as to minimize
potential damage to existing vegetation, utilities, landscape, or other Improvements.
6.6 STORAGE OF MATERIALS AND EQUIPMENT
All construction materials, equipment and vehicles will be stored within the fenced boundary of the
DRC-approved Construction Area. Equipment and machinery will be stored on-site only while
needed.
54
6.7 CONSTRUCTION ACTIVITY TIMES
The time of construction will be limited to the following (or as directed by Ironwood Security):
October 1st - April 30
Monday - Friday
7:00am - 5:30pm
Saturday
8:00am - 5:00pm
May 1st - September 30
Monday - Friday
6:00am - 7:00pm
Saturday
8:00am - 5:00pm
No construction operations may occur on Sundays, New Years Day, Memorial Day, Independence
Day, Labor Day, Thanksgiving Day, and Christmas Day or as may be prohibited by local
ordinance. Essentially quiet activities that do not involve heavy equipment or machinery may occur
at other times subject to the review and approval of the DRC. No personnel are to remain at the
Construction Site after working hours.
The United States Fish and Wildlife Service has imposed a halt on heavy construction within the
lambing season of the peninsular bighorn sheep, which extends from January 1-June 30. In the
past, including in adjacent developments, the USFWS has not construed this restriction to include
construction of single family residential homes. However, the agency, in its own discretion could
change its policy and impose additional restrictions on residential construction.
6.8 CONSTRUCTION TRAILERS AND/OR TEMPORARY
STRUCTURES
Any Owner or Builder who desires to bring a construction trailer or the like to Canyon View
Estates must obtain written approval from the DRC. The DRC will work closely with the Owner
and/or Builder to site the trailer in the best possible location to minimize impacts to the site and to
adjacent Parcel Owners. All such facilities will be removed from the Lot prior to issuance of a
Certificate of Occupancy. It is encouraged that construction trailers be painted tan.
Temporary living quarters for the Owner, Builder or their employees on the Lot will not be
permitted.
6.9 SANITARY FACILITIES
Sanitary facilities must be provided for construction personnel on-site in a location approved by the
DRC. The facility must be located in an area on-site that does not impact adjacent Residences and
Roads, maintained regularly, and be the color “The Reserve Tan.”
55
6.10 DEBRIS AND TRASH REMOVAL
Contractors must clean up all trash and debris on the Construction Site at the end of each day.
Trash and debris must be removed from each Construction Site at least once a week and
transported to an authorized disposal site. Lightweight material, packaging and other items must be
covered or weighted down to prevent wind from blowing such materials off the Construction Site.
Contractors are prohibited from dumping, burying • or burning trash anywhere on the Lot or in the
Ironwood Community. During the construction period, each Construction Site must be kept neat
and tidy to prevent it from becoming a public eyesore or affecting adjacent Lots. Dirt, mud or
debris resulting from activity on each Construction Site must be promptly removed from Roads,
open spaces and driveways or other portions of Canyon View Estates.
Any clean up costs incurred by the DRC or the Association in enforcing these requirements will be
taken out of the Builder’s Bond or billed to the Owner as needed.
6.11 HAZARDOUS WASTE MANAGEMENT
In order to be able to respond and monitor hazardous material use and/or spills, the Contractor shall
comply with the following criteria listed below:
The Contractor shall provide a contact person and telephone number for a company
experienced in emergency response for vacuuming and containing spills for oil or other
petroleum products.
Absorbent sheets will be used for spill prevention and clean up. Several boxes should be
located at fuel trucks, storage areas and in maintenance vehicles. Inventories must be
maintained as necessary.
A reportable spill is defined as a spill of one or more gallons and a significant spill is
defined as more than ten gallons.
The Contractor shall maintain a list of product names and a Materials Safety Data Sheet
(MSDS) for all hazardous material products used or located on site.
Before a hazardous material is stored, the Contractor shall check to ensure that:
o The material is stored in an approved container;
o The container is tightly closed;
o The container has the proper warning label; and
o The container is inspected for leaks.
6.12 EXCAVATION AND GRADING
During construction, erosion must be minimized on exposed cut and/or Fill slopes through proper
soil stabilization, water control and revegetation. Grading operations may be suspended by DRC
during periods of heavy rains or high winds. Blowing dust resulting from grading and construction
operations must be controlled by watering.
All topsoil disturbed by grading operations must be stockpiled and covered to minimize blowing
dust within the Construction Area and reused as part of the site restoration/landscaping plans.
Comply with Best Management Practice (BMP) South Coast Air Quality Management District
regulations for PM-10.
56
6.13 FOUNDATIONS
The Owner is encouraged to seek the assistance of a licensed Soil Engineer to examine and test soil
conditions on her/his Lot prior to undertaking any design or construction. Declarant makes no
representations or warranties, expressed or implied, as to the soil conditions.
The Owner and the Owner’s Architect, Engineer and Contractor shall give due
consideration to the design of the foundation systems of all structures.
It is the Owner’s responsibility to conduct an independent soils engineering investigation to
determine the suitability and feasibility of any Lot for construction of the intended
Improvement.
6.14 LOT SURVEY
Prior to commencement of design, it is the responsibility of the buyer to obtain a survey by a
Surveyor licensed in the State of California to confirm existing grades, tops and toes of slopes and
any other features or Lot attributes that would affect the design of any Lot Improvement. See
Appendix F - Lot Survey Requirements.
6.15 START OF CONSTRUCTION & TEMPORARY LANDSCAPE
All Improvements commenced on a Lot shall be completed within 18 months after commencement
according to approved Final Design Review plans unless an exception is granted in writing by the
DRC. If an Improvement is commenced and construction is then abandoned for more than 90 days,
or if construction is not completed within the required 18-month period, the Association may
impose a fine of not less than $100.00 per day (or such other reasonable amount as the Association
may set) to be charged against the Owner of the Lot until construction is resumed or the
Improvement is completed, as applicable, unless the Owner can prove to the satisfaction of the
Board that such abandonment is for circ*mstances beyond the Owner’s control.
For aesthetic and dust control reasons, the DRC may request Lot Owners who, in their opinion, are
not diligently pursuing construction to install a water meter, turf, irrigate and maintain their Lots.
Owners may elect to have the Association maintain the turf on their Lot for a monthly cost of $200,
excluding water cost.
6.16 DAMAGE REPAIR AND RESTORATION
Damage and scarring to other property, including open space, adjacent Parcels, Roads, Driveways,
Irrigation and/or other Improvements will not be permitted. If any such damage occurs, it must be
repaired and/or restored promptly at the expense of the person causing the damage or the Owner of
the Parcel.
1 To the Owner’s satisfaction, revegetate the area disturbed immediately and maintain said
vegetation until established; and,
2 Pay any fines imposed by the City of Palm Desert or other governmental agencies,
including but not limited to the California Department of Environmental Quality or the
South Coast Air Quality Management District, as a result of said violation.
57
6.17 PROJECT COMPLETION AND CLOSE-OUT
Upon completion of construction, each Owner and Builder will be responsible for cleaning up the
Construction Site and for the repair of all property that was damaged, including but not limited to
restoring grades, planting shrubs and trees as approved or required by the DRC, and repair of
streets, driveways, pathways, drains, culverts, ditches, signs, lighting and fencing. Any property
repair costs as mentioned above, incurred by the DRC or the Association, will be taken out of the
Builder’s Bond or billed to the Owner.
6.18 CONSTRUCTION OBSERVATIONS
In addition to the building inspections required by the City of Palm Desert, the following
construction observations must be scheduled with the DRC:
1 Site Observation – This observation includes review of staking of the Construction Area
including all corners of proposed buildings, driveways and extent of grading. In addition,
flagging of all areas to be protected will be reviewed. An on-site mock-up for color and
materials shall be constructed for approval by the DRC. A full-scale mock-up (minimum 4-
feet by 8- feet) shall be constructed which accurately conveys all proposed exterior
materials, colors, and detailing, including window, corner and trim details and/or details of
areas where one material changes to another. This observation must be approved by the
DRC prior to the framing observation.
2 Framing Observation – This observation must be done prior to enclosure of exterior walls
and roof. Final approval is contingent upon field mock-ups of all colors and materials at the
appropriate time in the construction process and in sizes / context that will allow a clear
understanding of the final product.
3 Final Walk Through Observation – The intent of this field review is to verify
construction was completed in substantial conformance with the DRC approved plans.
This observation should be done prior to the Certificate of Occupancy issued by the City of Palm Desert and may be scheduled when all Improvements, including all structures, landscaping and grading, have been completed. Any photographs or exhibits provided with the final observation letter are not meant to be to scale and are offered solely to provide illustrative identification of the applicable written comment. All observations are to be requested, in writing, by the Builder.
6.19 CONSTRUCTION SIGNS
Temporary construction signage will be limited to one sign per Homesite. The sign shall not
exceed six square feet of total area, and shall be located within ten-feet of the Construction Site
entrance. All construction signs must be reviewed and approved by the DRC prior to installation.
Layout for the sign must be submitted to the DRC ten working days prior to a regularly scheduled
meeting. Alternatively, the DRC may require the contractor to construct a standardized
construction sign. The contractor should contact the DRC prior to sign fabrication to confirm the
required sign type.
58
6.20 NO PETS
Construction personnel are prohibited from bringing pets, particularly dogs, into Canyon View
Estates.
6.21 SECURITY
Security precautions at the Construction Site may include temporary fencing approved by the DRC.
Security lights, audible alarms and guard animals will not be permitted.
6.22 NOISE
Builder will make every effort to keep noise to a minimum. Radios will not be allowed in order to
minimize disturbance to neighbors, golf and wildlife.
6.23 NO SMOKING
Smoking is only allowed in enclosed vehicles. Fines of up to $1,000 will be taken out of the
Builder’s Bond or billed to the Owner in the event that smoking occurs out of vehicles on a
Construction Site. Warning signs such as “No Smoking or Open Flame Allowed” must be posted at
the Construction Site.
6.24 NO FIREARMS
No firearms are allowed in Ironwood.
6.25 ALCOHOL/DRUGS
No alcohol or illegal drugs are allowed on the Ironwood property at anytime.
6.26 CONSTRUCTION PERSONNEL CONDUCT
Offensive, loud or unmannerly behavior exhibited by the Builder, its employees or subcontractors
is not allowed and will not be tolerated. Builder shall be responsible for the behavior of his
employees and subcontractors.
59
APPENDIX A DEFINITIONS
Unless the context otherwise specifies or requires, the following words or phrases when used in
these Design Guidelines shall have the following meanings:
Accessory Structure Any structure detached from the main Residence a minimum of ten feet.
Architect A person licensed to practice architecture or landscape architecture in the State of California.
Association See definition contained in the CC&R’s.
Board See definition contained in the CC&R’s.
Builder A person or entity engaged by an Owner for the purpose of constructing any Improvement within.
The Builder and Owner may be the same person or entity.
Builder’s Bond The deposit that is required to be delivered to the DRC prior to commencing Construction Activity.
Building Coverage The total area of a Lot covered by building(s). Measured from outside of all exterior walls at
ground level, it includes all exterior stairways, covered parking, covered terraces, “outdoor rooms”
and walkway areas. It does not include roof overhangs, uncovered walkways, terrace or pool/spa
areas or above-grade decks.
Building Envelope That portion of any Parcel, designated as Private and Transition Areas (or Building Envelope) on
the Final Map, and within which the construction of buildings and accessory and appurtenant
structures and Improvements is located.
Common Areas See definition contained in the CC&R’s.
Community All the property, and anything else that is part of the specific areas owned by private Lot Owners,
Homeowners Association, Common Areas, and golf club within the boundary of the Ironwood
Country Club.
Construction Activity Any site disturbance, construction, addition or alteration of any building, landscaping or any other
Improvement on any Construction Site.
60
Construction Site A site upon which Construction Activity takes place.
Construction Vehicle Any car, truck, tractor, trailer or other vehicle used to perform any part of a Construction Activity
or to transport equipment, supplies or workers to a Construction Site.
Declarant See definition contained in the CC&R’s.
Design Guidelines The architectural, regulations, restrictions and review procedures adopted and enforced by the
DRC as set forth in this document and as amended from time to time by the DRC.
Design Review Committee (DRC) The DRC appointed by the Declarant or the Ironwood Association Board as provided in the
CC&R’s to review and either approve or disapprove proposals and/or plans and specifications for
the construction, exterior additions, landscaping, or changes and alterations within Ironwood.
Excavation Any disturbance of the surface of the land (except to the extent reasonably necessary for planting
of approved vegetation), including any trenching that results in the removal of earth, rock or other
substance from a depth of more than 12-inches below the existing surface of the land or any
grading of the surface.
Fill Any addition of earth, rock or other materials to the surface of the land, which increases the
existing elevation of such surface.
Final Map The recorded final Subdivision map or Parcel map for any portion of Ironwood.
Floor Area The sum of all horizontal Floor Areas of a building measured from the outside of all exterior walls
and that is a conditioned space.
Homesite or Lot Diagram The term Homesite or Lot Diagram shall refer to the individual site plans for each Parcel provided
to the Owner by the DRC at the commencement of the Design Review Process. Each Homesite
Diagram specifies setbacks, Building Height and any special restrictions pertinent to the Parcel’s
development as recorded with the City of Palm Desert, together with any additional factors that the
DRC may consider to be pertinent.
Homeowner See definition for Owner.
Improvements See Definition contained in the CC&R’s.
61
Lot See definition contained in the CC&R’s.
Minimum Floor Area Minimum Floor Area is described in section 2.6 (Floor Area is defined as in Floor Area, above).
Natural Area The Natural Area is that portion of the Lot that lies outside the Building Envelope and must remain
in an essentially landscaped condition in accordance with these Guidelines.
Neighborhood All the property, and anything else that is part of the specific areas owned by private Lot Owners,
Homeowners Association, and Common Areas.
Owner See definition contained in the CC&R’s.
Parcel The term “Parcel” shall be those Parcels of land, together with any appurtenances, described as
Lots 1-52 subdivided by Declarant pursuant to the City of Palm Desert subdivision approval for the
Ironwood Property.
Private Area The Private Area is that portion of the Building Envelope in which all vertical Improvements must
occur.
Residence See definition contained in the CC&R’s.
Story That portion of any building (including garage) included between the surface of any floor and the
surface of the floor above it, or if there is no floor above, then the space between the floor and the
ceiling next above it. Any portion of a Story exceeding 18-feet in height shall be considered as an
additional Story for each 18-feet or fraction thereof. If the finished floor level directly above a
basem*nt or cellar is more than six feet above grade, such basem*nt or cellar shall be considered a
Story.
Transition Area The Transition Area is that portion of the Building Envelope which is visible from the golf course
or other Common Areas, streets and neighboring Lots and is adjacent to the Natural Area.
Visual Building Mass A Visual Building Mass shall have a minimum depth and width of at least twenty (20) feet, be a
minimum of five hundred (500) square feet in area, and be offset by at least two (2) feet
horizontally and three (3) feet vertically from an adjacent mass.
62
APPENDIX B ROOF FORM TABLE The following Lots are required to conform to the roofing guidelines with regard to the use of flat
roofs. Some special considerations may be made if in conjunction with a solar application.
Lot Number
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
27
28
29
63
APPENDIX C APPROVED PLANT LIST
Botanical Name Common Name Areas
Private Transition Natural
Trees Acacia aneura Mulga Acacia x x x Acacia berlandieri Guajillo x x x Acacia greggii Catclaw Acacia x x Acacia salicina Willow Wattle x Acacia saligna Golden Wreath Wattle x Acacia schaffneri Twisted Acacia x x x Acacia smallii Sweet Acacia x x x Acacia willardiana Palo Blanco x x Bauhinia congesta Anacacho Orchid Tree x Bauhinia species Orchid Tree x Callistemon viminalis Bottle Tree x Caesalpinia cacalaco Cascalote x x x Caesalpinia mexicana Mexican Bird of Paradise x x x Ceratonia siliqua Carob Tree x Cercidium floridum Blue Palo Verde x x x Cercidium hybrid Hybrid Palo Verde x x x
‘Desert Museum’ Cercidium praecox Palo Brea x x x Cercidium microphyllum Foothill Palo Verde x Cercis occidentalis Western Redbud x Chilopsis linearis Desert Willow x x x Citrus species Citrus tree x Eriobotrya japonica Loquat x Ficus species Ficus x Fortunella margarita Dwarf Kumquat x Geijera parviflora Australian Willow x Lagerstroemia indica Crape Myrtle x Lysiloma thornberi Feather Tree x Olea europea ‘Swan Hill’ or ‘Wilsonia’ Fruitless Olive Tree x
Olneya tesota Ironwood x x x Pistacia species Pistacia x Pithecellobium flexicaule Texas Ebony x x Prosopis chilensis Chilean Mesquite x x x Prosopis glandulosa Honey Mesquite x x x Prunus cerasifera Purple Leaf Plum x Prunus species Peach, Nectarine, Plum x Psurothamnus spinosa Smoke Tree x x Quercus virginiana Southern Live Oak x Rhus lancea African Sumac x Schinus molle California Pepper x Sophora secundiflora Texas Mountain Laurel x
64
Botanical Name Common Name Private
Areas
Transition
Natural Shrubs Alyogyne huegelii Blue Hibiscus x Bougainvillea spp. Bougainvillea x x x Buddleia marrubifolia Wooly Butterfly Bush x x Caesalpinia gilliesii Yellow Bird of Paradise x x Caesalpinia pulcherrima Red Bird of Paradise x x x Calliandra californica Baja Fairy Duster x x x Calliandra eriophylla Pink Fairy Duster x x x Carissa grandiflora Natal Plum x Cassia nemophylla Desert Cassia x x x Chrysactinia mexicana Damianita x x x Clivia miniata Kaffir Lily x Cordia parvifolia Littleleaf Cordia x x x Dalea dorycinoides ‘Cerro Azul’ ‘Cerro Azul’ Dalea x x Dalea frutescens Black Dalea x x x Dalea lutea ‘Sierra Moonrise’ ‘Sierra Moonrise’ Dalea x x Dalea pulchra Bush Dalea x x x Dicliptera suberecta Velvet Honeysuckle x Dodonea viscosa Hopbush x x x Encelia farinosa Brittlebush x x x Ericameria laricifolia Turpentine Bush x x x Euryops pectinatus Euryops x Euryops viridis Green Euryops x Feijoa sellowiana Pineapple Guava x Gardenia jasminoides Gardenia x Hibiscus rosa-sinensis Chinese Hibiscus x Hyptis emoryi Desert Lavender x x x Isomeris arborea Bladderpod x x x Justicia californica Chuparosa x x x Justicia spicigera Desert Honeysuckle x Lantana camara ‘Radiation’ ‘Radiation’ Bush Lantana x Larrea tridentata Creosote x x x Leucophyllum frutescens Texas Ranger x x x
‘White’, ‘Green’, or ‘Silver’ Leucophyllum laevigatum Chihuahuan Sage x x Leucophyllum zygophyllum Blue Ranger x x x Liriope gigantea Giant Lily Turf x Myrtus communis Myrtle x Nandina spp. Heavenly Bamboo x Philodendron selloum Philodendron x Photina fraser Fraser Photinia x Pittosporum tobira
‘Wheeler’s Dwarf ’ x Plumbago species Plumbago x Prunus caroliniana Carolina Laurel Cherry x Punica granatum Pomegranate x Pyracantha species Pyracantha x Raphiolepis indica India Hawthorn x Rosa varieties Rose x Rosemarinus officinalis Upright Rosemary x Rhus ovata Sugar Bush x Ruella brittoniana ‘Katie’ Wild Petunia x x x Ruella peninsularis Baja Ruella x x x Salvia clevelandii Chapparral Sage x x x Salvia dorrii Dorrii Sage x x x Salvia greggii Autumn Sage x x x Salvia leucantha Mexican Sage x x x
65
Botanical Name Common Name Private
Areas
Transition
Natural Santolina spp. Lavender Cotton x Simmondsia chinesis Jojoba x x x Tecoma stans Yellow Bells x Tecomaria capensis Cape Honeysuckle x Tagetes lemmonii Mt. Lemon Marigold x Viguiera deltoidea Goldeneye x x Xylosoma congestum Shiny Xylosoma x Zauschneria californica California Fuschia x
Palms Brahea armata Mexican Blue Fan Palm x Brahea edulis Guadalupe Palm x Chamaerops humilis Mediterranean Fan Palm x Cycas revoluta Sago Palm x Phoenix canariensis Canary Island Palm x Phoenix dactylifera Date Palm x Phoenix reclinata Senegal Date Palm x Phoenix roebelenii Pigmy Palm x Washingtonia filifera California Fan Palm x x x
Ground Covers Acacia redolens ‘Desert Carpet’ Prostrate Acacia x x Asparagus species Asparagus Fern x Asparagus sprengeri Asparagus Fern x Ambrosia deltoidea Bursage x x x Baccharis ‘Centennial’ Coyote Brush x x x Cerastium tomentosum Snow-in-Summer x Convolvulus species Silver Bush Morning Glory x Dalea capitata ‘Sierra Gold’ ‘Sierra Gold’ Dalea x x x Dalea greggii Trailing Indigo Bush x x x Eriogonum fasciculatum Flattop Buckwheat x x x Gazania rigens Gazania x Lantana ‘New Gold’ ‘New Gold’ Lantana x x x Lantana ‘Trailing Yellow’ ‘Trailing Yellow’ Lantana x Lantana sellowiana Purple Lantana x x x Myoporum parvifolium Prostrate Myoporum x Oenothera spp. Primrose x x x Potentilla verna Spring Cinquefoil Rosmarinus officinalis Rosemary x
Setcreasea pallida
Purple Heart Plant
x Teucrium chamaedrys Germander x Thymus spp. Thyme x Trachelspermum jasminoides Star Jasmine x Verbena spp. Verbena x x x Vinca major Periwinkle x Zauschneria californica California Fuschia x x
x ‘Huntington Carpet’
66
Botanical Name Common Name Private
Areas
Transition
Natural Vines Antigonon leptotus Queen’s Wreath x Bignonia violacea Lavender Trumpte Vine x Bougainvillea brasiliensis Bougainvillea x x Campsis radicans Trumpet Creeper x Clyostoma callistegioides Lavender Trumpet Vine x Ficus pumila Creeping Fig x Gelsemium sempervirens Carolina Jessamine x Jasminum polyanthum Pink Flowering Jasmine x Lonicera japonica ‘Halls’ Halls Honeysuckle x Macfadyena unguiscati Cat’s Claw x Passiflora species Passion Vine x Podranea ricasoliana Pink Trumpet Vine x Pyracantha coccinea Pyracantha x Rosa banksiae Lady Bank’s Rose x Rosa species Rose Vine x Tecomaria capensis Cape Honeysuckle x Trachelospermum jasminoiides Star Jasmine x
Cactus, Succulents and Desert Emphatics
Agave spp. (1)
Agave
x
x
x Aloe spp. (1)
Cereus peruvianus
Dasylirion spp.
Aloe
Peruvian Apple Cactus
Desert Spoon
x
x
x
x
x
x
x
Echinocerus spp.
Ferocactus spp.
Fouquiera splendens
Hesperaloe parviflora
Lophocereus schottii
Nolina spp.
Opuntia bigelovii
Opuntia lindheimeri
var. linguiformis
Opuntia santa rita
Yucca baccata
Yucca elata
Yucca pendula
Yucca rigida
Yucca rostrata
Yucca thompsoniana
Hedgehog Cactus
Barrel Cactus
Octillo
Red and Yellow Hesperaloe
Totem Pole Cactus
Beargrass
Teddy Bear Cholla
Cow’s Tongue Prickly Pear
‘Santa Rita’ Prickly Pear
Banana Yucca
Soaptree Yucca
Pendulous Yucca
Blue Yucca
Beaked Yukka
Thompson Yucca
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
Wildflowers
Abronia villosa
Sand Verbena
x
x
x
Dimorphotheca sinnuata
Eschscholzia californica
Gaillardia spp.
Lupinis arizonicus
African Daisy
California Gold Poppy
Indian Blanket
Arizona Lupine
x
x
x
x
x
x
x
x
x Orthocarpus exserta
Phacelia campanularia
Psilostrophe tagetina
Zinna acerosa
Purple Owl’s Clover
Desert Canterburybells
Paperflower
Desert Zinna
x
x
x
x
x
x
x
x
x
x
x
x
67
Botanical Name Common Name Private
Areas
Transition
Natural Ornamental Grasses Achnatherum hymenoides Indian Rice Grass x Agropyron desertorum Desert Wheat Grass x Bouteloua aristiodes Black Gramma Grass x Muhlenbergia capillaris Deergrass x Muhlenbergia rigens Deergrass x x x
Pennisetum setaceum cupreum Purple Fountain Grass x
Native Grasses Bouteloua gracilis Blue Gramma x x Oryzopsis hymenoides Indian Rice Grass x x Panicum urvilleneum Panic Grass x x Stipa speciosa Needle Grass x x
Perennials Abronia villosa Sand Verbena x Agapanthus species Lily of the Nile x Aquilegia chrysantha Golden-spurred Columbine x Aspidistra elatior Cast-iron Plant x Baileya multiradiata Desert Marigold x x x Cassia covesii Desert Senna x Centaurea cineraria Dusty Miller x Coreopsis grandiflora Coreopsis x Cyperus alternifolius Umbrella Plant x Dietes bicolor or vegeta Fortnight Lily x Dimorphothecha sinuata African Daisy x Dyssodia pentachaeta Golden Fleece x Echinacea angustifolia Echinacea x Eschscholzia species Mexican/California Poppy x Fatsia japonica Japanese Aralia x Hemerocallis spp. Daylily x Hymenoxys acaulis Angelita Daisy x x Iris spp. Iris x Kniphofia uvaria Red-Hot Poker x Lavandula spp. Lavender x Lupine arizonicus Arizona Lupine x Melampodium leucanthum Blackfoot Daisy x x x Narcissus species Daffodills x Nemophila maculata Five Spot x Penstemon spp. Penstemon x x Phacelia crenulata Desert Bluebells x Phacelia tanacetifolia Desert Globemallow x Rudbeckia hirta Gloriosa Daisy x Santolina species Santolina x Spaeralcea coccinea Scarlet Globe Mallow x Sphaeralcea ambigua Globe Mallow x x x Strelitzia reginae Bird of Paradise x Teucrium chamaedrys Germander x Zantedescia aethiopica Calla Lily x Zinnia grandiflora Prairie Zinnia x x
67
APPENDIX D PROHIBITED PLANT MATERIALS
Botanical Name
Arundo donax
Cortaderi spp.
Cystisus spp.
Genista spp.
Spartium juncea
Tamarix spp.
Common Name
Carrizo
Pampas Grass
Various Brooms
Various Brooms
Spanish Broom
Invasive
Invasive
Invasive
Invasive
Invasive
Invasive
* Any plant listed as noxious by California Department of Food and Agriculture:
1. All Pines, Cypress, False Cypress, Juniper or Cedar for aesthetic reasons.
2. Olive and Mulberry trees for aesthetic reasons due to pollen producing concerns.
Fruitless Olive will be allowed within private gardens.
3. Oleanders and Thevetia for aesthetic reasons and due to pollen and poison
concerns.
4. Fountain Grass (Pennisetum setaceum) due to weed-like growth habit and fire
concerns.
5. Common Bermuda (Cynodon dactylon) due to its weed-like growth habits.
6. Mexican Palo Verde (Parkinsonia aculeata) due to its weed-like growth habits.
7. Brazilian Pepper, Eucalyptus and Bottle trees for aesthetic and scale reasons.
Limited accent use of California Pepper and African Sumac, occurring only where
other groves occur in order to preserve the
68
APPENDIX E GOVERNING REGULATIONS
All proposed Improvements shall comply with the following regulations:
• This Guideline document.
• The Declaration of Covenants, Conditions and Restrictions for the Canyon View Estates at
Ironwood Country Club.
• All applicable City of Palm Desert Ordinances, Regulations and Codes.
• All applicable regulations under the jurisdiction of the Coachella Valley Water District
(CVWD).
• All applicable Local, State and Federal Codes and Regulations.
• Any conditions of approval issued for this project by a regulatory agency.
69
APPENDIX F LOT SURVEY REQUIREMENTS
The following information shall be included in all surveys of individual Lots at Canyon View
Estates. These standards will allow for easier review and coordination of the designs within the
entire project.
All drawings should be drawn in AutoCAD R14 or later with the coordinate system and vertical
datum conforming to the project engineer’s coordinate system, which will be provided at the
request of the surveyor. All AutoCAD entities (line types, colors, ect.) to be ‘by layer.’ All line type
scales set at 1. Survey drawn at 1/1 formatted in architectural units. The survey is to be plotted at 1”
= 20’ for review purposes. X-refs should be placed on individual specific layers (i.e., x-diagram).
The following items should be shown on separate layers: property boundaries; Building Envelope
and Transition Areas; easem*nts; all utilities including but not limited to the following:
Electrical
Potable water
Gas
Fiber optics/Cable TV lines
Non-potable irrigation water service (if applicable)
At a minimum, the following will be shown on the survey and extend 20 feet past the property
boundary on all sides:
Property boundaries
Street edge of pavement
Easem*nts
Utilities and/or site features
One foot topographic information
Location and finished floor of existing structures on adjacent Lots
Existing vegetation, particularly in the golf course or in Developer-landscaped areas.
Location of existing lakes (if applicable)
Rock outcrops with spot grades at base and high points (if applicable)
Existing trees with spot grades at trunk. Type of tree to be shown with trunk diameter and
approximate height and spread canopy
Existing walls with TW and BW grades, if any
Edges of existing pavement
All Lots are to show grades drawn with polylines in the following manner - 1’ contours and 10’
contours shown on separate layers with zero width to polylines. Other information may be required
by the permitting authorities, and it is the Lot surveyor’s responsibility to ensure that the survey
meets those requirements.
70
APPENDIX G DESIGN REVIEW APPLICATION FORMS
71
CANYON VIEW ESTATES
Design Review Application
Application d ate:
Type of Review Requested: Schematic Design Preliminary Design Final O t h e r
Application Fees: $3,500 (Fee must be paid with Pre-Design Conference or Schematic Design Request Form)
1. Application will be accepted after all information as noted in Chapter 5 of the Design Guidelines
has been provided.
A meeting will be scheduled based on the set meeting schedule when a complete submission is received.
2. Please contact the Association Manager regarding application questions.
Section I - Project Information
A. Lot:
B. Location of Project
Street Address:
C. Name of Owner(s):
Street Address:
City: State: Zip Code:
Telephone: ( ) E-mail:
D. Name of Architect: Firm:
Street Address:
City: State: Zip Code:
Telephone: ( ) E-mail:
E. Name of Landscape Architect: Firm:
Street Address:
City: State: Zip Code:
Telephone: ( ) E-mail:
I have read and will comply with the Canyon View Estates at Ironwood Country Club Design Guidelines concerning construction
activities and the Covenants, Conditions, Restrictions and Reservation of Easem*nts (CC& R's) for Canyon View Estates at
Ironwood Country Club.
Signature and Printed Name of Signatory Date
Square Footages:
o Main Residence: _____
o Garages: _____
o Mechanical: _____
o Accessory Structures: _____
o Miscellaneous: _____
o Total Conditioned Space _____
C A N Y O N V I E W E S T A T E S D E S I G N G U I D E L I N E S
D E C E M B E R 2 0 0 3 - P A G E G - 72
APPENDIX H ILLUSTRATIONS AND SITE PHOTOS
Contact Association Office for illustrations and site photos as necessary.